mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
a873b29284
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
1-VCC ; 2-TX ; 3-RX; 4-GND;
Serial 115200-8-N-1.
Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button
Need Testing:
- WPS button
Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
can now navigate to 192.168.1.1 to your new OpenWrt installation.
Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
you can (doing it with LuCI is easy and can be done in the same step).
Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
last working firmware - you should be able to access your router on
LAN.
Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
client method.
Back To Stock:
- Use the generic recovery using the tftp client method to flash the
"civic.img". Also you can strip-and-pad the original image and use
the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
booted.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
35 lines
1.2 KiB
Bash
Executable File
35 lines
1.2 KiB
Bash
Executable File
#!/bin/sh /etc/rc.common
|
|
#
|
|
# This script sets auto_recovery to "yes" and resets the boot counter to 0.
|
|
# As a golden rule, this should be the latest script to run at boot. For a
|
|
# developer snapshot, it is fine to set auto_recovery here. But for a stable
|
|
# release, this script must in fact turn off auto_recovery.
|
|
#
|
|
# Why? Because the custom sysupgrade script for the device will turn on
|
|
# auto_recovery to "yes". And it's the job of this script to set the
|
|
# boot boot_count to 0 and then disable auto_recovery, as that condition
|
|
# means that the stable release went well.
|
|
#
|
|
# I have to repeat: this script should be changed for stable releases.
|
|
|
|
START=99
|
|
boot() {
|
|
. /lib/functions.sh
|
|
|
|
case $(board_name) in
|
|
linksys,ea6350v3)
|
|
# make sure auto_recovery in uboot is always on
|
|
IS_AUTO_RECOVERY="$(fw_printenv -n auto_recovery)"
|
|
if [ "$IS_AUTO_RECOVERY" != "yes" ] ; then
|
|
fw_setenv auto_recovery yes
|
|
echo "Linksys EA6350v3: fw_setenv: auto_recovery has been set to yes"
|
|
fi
|
|
# reset the boot counter
|
|
fw_setenv boot_count 0
|
|
mtd resetbc s_env
|
|
echo "Linksys EA6350v3: boot counter has been reset"
|
|
echo "Linksys EA6350v3: boot_part=$(fw_printenv -n boot_part)"
|
|
;;
|
|
esac
|
|
}
|