mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
0b20490207
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
74 lines
1.3 KiB
Bash
74 lines
1.3 KiB
Bash
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
platform_check_image() {
|
|
case "$(board_name)" in
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
local ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
local asus_root=$(nand_find_volume $ubidev jffs2)
|
|
|
|
[ -n "$asus_root" ] || return 0
|
|
|
|
cat << EOF
|
|
jffs2 partition is still present.
|
|
There's probably no space left
|
|
to install the filesystem.
|
|
|
|
You need to delete the jffs2 partition first:
|
|
# ubirmvol /dev/ubi0 --name=jffs2
|
|
|
|
Once this is done. Retry.
|
|
EOF
|
|
return 1
|
|
;;
|
|
esac
|
|
return 0;
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
case "$(board_name)" in
|
|
8dev,jalapeno)
|
|
nand_do_upgrade "$ARGV"
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
CI_KERNPART="linux"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_openmesh "$ARGV"
|
|
;;
|
|
meraki,mr33)
|
|
CI_KERNPART="part.safe"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
*)
|
|
default_do_upgrade "$ARGV"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
platform_nand_pre_upgrade() {
|
|
case "$(board_name)" in
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
CI_KERNPART="linux"
|
|
;;
|
|
meraki,mr33)
|
|
CI_KERNPART="part.safe"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
blink_led() {
|
|
. /etc/diag.sh; set_state upgrade
|
|
}
|
|
|
|
append sysupgrade_pre_upgrade blink_led
|