mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
37af596593
The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
76 lines
1.7 KiB
Bash
76 lines
1.7 KiB
Bash
#!/bin/sh
|
|
|
|
rt2x00_eeprom_die() {
|
|
echo "rt2x00 eeprom: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
rt2x00_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_part $part)
|
|
[ -n "$mtd" ] || \
|
|
rt2x00_eeprom_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
jboot_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_part $part)
|
|
[ -n "$mtd" ] || \
|
|
rt2x00_eeprom_die "no mtd device found for partition $part"
|
|
|
|
jboot_config_read -i $mtd -o $offset -e /lib/firmware/$FIRMWARE 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
rt2x00_eeprom_set_macaddr() {
|
|
local macaddr=$1
|
|
|
|
[ -n "$macaddr" ] || \
|
|
rt2x00_eeprom_die "invalid wlan mac address"
|
|
|
|
macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \
|
|
conv=notrunc bs=1 seek=4 count=6 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to write mac address to eeprom file"
|
|
}
|
|
|
|
FW="/lib/firmware/$FIRMWARE"
|
|
[ -e "$FW" ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"soc_wmac.eeprom")
|
|
case $board in
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-118-a2|\
|
|
dlink,dwr-921-c1)
|
|
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
|
wifi_mac=$(macaddr_add "$wan_mac" 1)
|
|
jboot_eeprom_extract "config" 0xE000
|
|
rt2x00_eeprom_set_macaddr $wifi_mac
|
|
;;
|
|
tiny-ac)
|
|
wifi_mac=$(mtd_get_mac_ascii u-boot-env INIC_MAC_ADDR)
|
|
rt2x00_eeprom_extract "factory" 0 512
|
|
rt2x00_eeprom_set_macaddr $wifi_mac
|
|
;;
|
|
*)
|
|
rt2x00_eeprom_die "Please define mtd-eeprom in $board DTS file!"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|