mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-01 19:46:51 +00:00
9dd4ba3d7e
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
164 lines
2.6 KiB
Plaintext
164 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
compatible = "tplink,eap245-v3", "qca,qca9563";
|
|
model = "TP-Link EAP245 v3";
|
|
|
|
aliases {
|
|
led-boot = &led_status_green;
|
|
led-failsafe = &led_status_amber;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_amber;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_green: status_green {
|
|
label = "tp-link:green:status";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_status_amber: status_amber {
|
|
label = "tp-link:amber:status";
|
|
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "factory-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot";
|
|
reg = <0x040000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "partition-table";
|
|
reg = <0x080000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@90000 {
|
|
label = "info";
|
|
reg = <0x090000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@a0000 {
|
|
label = "art";
|
|
reg = <0x0a0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@b0000 {
|
|
label = "extra-para";
|
|
reg = <0x0b0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
compatible = "openwrt,elf";
|
|
label = "firmware";
|
|
reg = <0x0c0000 0xe40000>;
|
|
};
|
|
|
|
partition@f00000 {
|
|
label = "config";
|
|
reg = <0xf00000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f30000 {
|
|
label = "mutil-log";
|
|
reg = <0xf30000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fb0000 {
|
|
label = "oops";
|
|
reg = <0xfb0000 0x040000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0x1>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PAD0 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0xe0 0xc74164de /* SGMII_CTRL */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "sgmii";
|
|
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|