mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
b7a9a183fb
Hardware -------- RockChip RK3328 ARM64 (4 cores) 1GB DDR4 RAM 2x 1000 Base-T 3 LEDs (LAN / WAN / SYS) 1 Button (Reset) Micro-SD slot USB 2.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card using dd. MAC-address ----------- The vendor code supports reading a MAC address from an EEPROM connected via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC address in binary at offset 0xfa. However, my two units didn't come with such an EEPROM soldered on. The EEPROM should be placed between the SoC and the GPIO pins on the board. (U10) Generating rendom MAC addresses works around this issue. Otherwise, all boards running the same image have identical MAC addresses. Signed-off-by: David Bauer <mail@david-bauer.net>
63 lines
1.8 KiB
Diff
63 lines
1.8 KiB
Diff
From: William Wu <william.wu@rock-chips.com>
|
|
|
|
RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
|
|
core's general architecture. It can act as static xHCI host
|
|
controller, static device controller, USB 3.0/2.0 OTG basing
|
|
on ID of USB3.0 PHY.
|
|
|
|
Signed-off-by: William Wu <william.wu@rock-chips.com>
|
|
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
|
|
|
|
---
|
|
|
|
NOTE: This binding still has issues. From the original thread:
|
|
|
|
the rk3328 usb3-phy has an issue with detecting any plugin events
|
|
after a previous device got removed - see the inno-usb3-phy driver
|
|
in the vendor kernel.
|
|
|
|
The current state is good-enough for enabling the USB3 attached LAN
|
|
port of the NanoPi R2S. However, it might explode depending on your
|
|
use-case. You've been warned.
|
|
|
|
---
|
|
arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++++
|
|
1 file changed, 27 insertions(+)
|
|
|
|
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
|
|
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
|
|
@@ -936,6 +936,33 @@
|
|
status = "disabled";
|
|
};
|
|
|
|
+ usbdrd3: usb@ff600000 {
|
|
+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3";
|
|
+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>,
|
|
+ <&cru ACLK_USB3OTG>;
|
|
+ clock-names = "ref_clk", "suspend_clk",
|
|
+ "bus_clk";
|
|
+ #address-cells = <2>;
|
|
+ #size-cells = <2>;
|
|
+ ranges;
|
|
+ status = "disabled";
|
|
+
|
|
+ usbdrd_dwc3: dwc3@ff600000 {
|
|
+ compatible = "snps,dwc3";
|
|
+ reg = <0x0 0xff600000 0x0 0x100000>;
|
|
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
|
|
+ dr_mode = "otg";
|
|
+ phy_type = "utmi_wide";
|
|
+ snps,dis_enblslpm_quirk;
|
|
+ snps,dis-u2-freeclk-exists-quirk;
|
|
+ snps,dis_u2_susphy_quirk;
|
|
+ snps,dis_u3_susphy_quirk;
|
|
+ snps,dis-del-phy-power-chg-quirk;
|
|
+ snps,dis-tx-ipgap-linecheck-quirk;
|
|
+ status = "disabled";
|
|
+ };
|
|
+ };
|
|
+
|
|
gic: interrupt-controller@ff811000 {
|
|
compatible = "arm,gic-400";
|
|
#interrupt-cells = <3>;
|