openwrt/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
Bernhard Frauendienst 480bf28273 ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
    WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
    Diag red, Movie Engine blue, USB green)

It is already supported by the ar71xx target.

For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>

Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
  - via TFTP rescue
  - via factory image
    - on firmware v1.77 (28-05-2012)
    - on pro firmware v24SP2 r30356 (26-03-2018)
  - via sysupgrade from ar71xx
    (wlan devices don't work because of new names)
  - via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)

Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-09-10 09:35:07 +02:00

192 lines
4.1 KiB
Bash

#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions.sh
. /lib/functions/system.sh
ath9k_eeprom_die() {
echo "ath9k eeprom: " "$*"
exit 1
}
ath9k_eeprom_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath9k_eeprom_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath9k_eeprom_die "failed to extract from $mtd"
}
ath9k_eeprom_extract_reverse() {
local part=$1
local offset=$2
local count=$3
local mtd
local reversed
local caldata
mtd=$(find_mtd_chardev "$part")
reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd)
for byte in $reversed; do
caldata="\x${byte}${caldata}"
done
printf "%b" "$caldata" > /lib/firmware/$FIRMWARE
}
xor() {
local val
local ret="0x$1"
local retlen=${#1}
shift
while [ -n "$1" ]; do
val="0x$1"
ret=$((ret ^ val))
shift
done
printf "%0${retlen}x" "$ret"
}
ath9k_patch_fw_mac() {
local mac=$1
local mac_offset=$2
local chksum_offset=$3
local xor_mac
local xor_fw_mac
local xor_fw_chksum
[ -z "$mac" -o -z "$mac_offset" ] && return
[ -n "$chksum_offset" ] && {
xor_mac=${mac//:/}
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
}
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$mac_offset count=6
}
ath9k_patch_fw_mac_crc() {
local mac=$1
local mac_offset=$2
local chksum_offset=$((mac_offset - 10))
ath9k_patch_fw_mac "${mac}" "${mac_offset}" "${chksum_offset}"
}
board=$(board_name)
case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
avm,fritz4020)
ath9k_eeprom_extract_reverse "urlader" 5441 1088
;;
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"ath9k-eeprom-pci-0000:00:00.0.bin")
case $board in
avm,fritz300e)
ath9k_eeprom_extract_reverse "urloader" 5441 1088
;;
buffalo,whr-g301n|\
tplink,tl-wr841-v5|\
tplink,tl-wr941-v4)
ath9k_eeprom_extract "art" 4096 3768
;;
ocedo,raccoon|\
tplink,tl-wdr3600|\
tplink,tl-wdr4300|\
tplink,tl-wdr4900-v2)
ath9k_eeprom_extract "art" 20480 1088
;;
netgear,wnr612-v2|\
on,n150r|\
pcs,cap324|\
tplink,tl-mr3220-v1|\
tplink,tl-mr3420-v1|\
tplink,tl-wr2543-v1|\
tplink,tl-wr740n-v1|\
tplink,tl-wr740n-v3|\
tplink,tl-wr741-v1|\
tplink,tl-wr743nd-v1|\
tplink,tl-wr841-v7|\
ubnt,bullet-m|\
ubnt,nano-m|\
ubnt,rocket-m)
ath9k_eeprom_extract "art" 4096 4096
;;
ubnt,unifi)
ath9k_eeprom_extract "art" 4096 2048
;;
wd,mynet-wifi-rangeextender)
ath9k_eeprom_extract "art" 4096 4096
ath9k_patch_fw_mac_crc $(nvram get wl0_hwaddr) "$mac" 2
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"ath9k-eeprom-pci-0000:00:11.0.bin")
case $board in
buffalo,wzr-hp-ag300h|\
netgear,wndr3700|\
netgear,wndr3700v2|\
netgear,wndr3800)
ath9k_eeprom_extract "art" 4096 3768
;;
dlink,dir-825-b1)
ath9k_eeprom_extract "caldata" 4096 3768
ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"ath9k-eeprom-pci-0000:00:12.0.bin")
case $board in
buffalo,wzr-hp-ag300h|\
netgear,wndr3700|\
netgear,wndr3700v2|\
netgear,wndr3800)
ath9k_eeprom_extract "art" 20480 3768
;;
dlink,dir-825-b1)
ath9k_eeprom_extract "caldata" 20480 3768
ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
esac