mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 06:08:08 +00:00
f07e572f64
bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 3B v1.2 and RPi 4B v1.1 4G bcm2710: boot tested on RPi 3B v1.2 bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
56 lines
2.1 KiB
Diff
56 lines
2.1 KiB
Diff
From 0fec1c81707f5335d0b04b5e97d2ddd0b902377b Mon Sep 17 00:00:00 2001
|
|
From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
|
|
Date: Tue, 10 Mar 2020 14:17:07 +0100
|
|
Subject: [PATCH] media: i2c: imx219: Fix power sequence
|
|
|
|
Commit ca45448a56659c6df6e0436188e97f6cc65dea8a upstream.
|
|
|
|
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
|
|
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
|
|
state.
|
|
|
|
The powerup sequence in the datasheet[1] shows the sensor entering into
|
|
LP-11 in streaming mode, so to fix this issue transitions are performed
|
|
from "streaming -> standby" in the probe() after power up.
|
|
|
|
With this commit the sensor is able to enter LP-11 mode during power up,
|
|
as expected by some CSI-2 controllers.
|
|
|
|
[1] https://publiclab.org/system/images/photos/000/023/294/original/
|
|
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
|
|
|
|
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
|
|
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
---
|
|
drivers/media/i2c/imx219.c | 17 +++++++++++++++++
|
|
1 file changed, 17 insertions(+)
|
|
|
|
--- a/drivers/media/i2c/imx219.c
|
|
+++ b/drivers/media/i2c/imx219.c
|
|
@@ -1224,6 +1224,23 @@ static int imx219_probe(struct i2c_clien
|
|
/* Set default mode to max resolution */
|
|
imx219->mode = &supported_modes[0];
|
|
|
|
+ /* sensor doesn't enter LP-11 state upon power up until and unless
|
|
+ * streaming is started, so upon power up switch the modes to:
|
|
+ * streaming -> standby
|
|
+ */
|
|
+ ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
|
|
+ IMX219_REG_VALUE_08BIT, IMX219_MODE_STREAMING);
|
|
+ if (ret < 0)
|
|
+ goto error_power_off;
|
|
+ usleep_range(100, 110);
|
|
+
|
|
+ /* put sensor back to standby mode */
|
|
+ ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
|
|
+ IMX219_REG_VALUE_08BIT, IMX219_MODE_STANDBY);
|
|
+ if (ret < 0)
|
|
+ goto error_power_off;
|
|
+ usleep_range(100, 110);
|
|
+
|
|
ret = imx219_init_controls(imx219);
|
|
if (ret)
|
|
goto error_power_off;
|