openwrt/target/linux/ath79/dts/ar7240_buffalo_whr-g301n.dts
INAGAKI Hiroshi 9e6f22e309 ath79: add support for Buffalo WHR-G301N
Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240.
Ported from ar71xx target.

Specification:

- Atheros AR7240
- 32 MB of RAM
- 4 MB of Flash
- 2.4 GHz 2T2R wifi
- 5x 10/100 Mbps Ethernet
- 9x LEDs, 4x keys
  - LED: 8x gpio-leds, 1x ath9k-leds
  - key: 2x buttons, 1x slide switch
- UART header on PCB
  - Vcc, GND, TX, RX from LEDs side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WHR-G301N
2. Connect power cable to WHR-G301N and turn on it
3. Access to "http://192.168.11.1/" and open firmware update page
("ファーム更新")
4. Select the OpenWrt factory image and click execute ("実行") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[fix the SUPPORTED_DEVICES to be compatible with the ar71xx image]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00

193 lines
3.2 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar7240.dtsi"
/ {
compatible = "buffalo,whr-g301n", "qca,ar7240";
model = "Buffalo WHR-G301N";
aliases {
led-boot = &diag;
led-failsafe = &diag;
led-upgrade = &diag;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
poll-interval = <20>;
router_on {
label = "router_on";
linux,code = <BTN_2>;
linux,input-type = <EV_SW>;
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
router_off {
label = "router_off";
linux,code = <BTN_3>;
linux,input-type = <EV_SW>;
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&switch_led_pins>;
security {
label = "whr-g301n:orange:security";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
diag: diag {
label = "whr-g301n:red:diag";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
router {
label = "whr-g301n:green:router";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
lan1 {
label = "whr-g301n:green:lan1";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
lan2 {
label = "whr-g301n:green:lan2";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
lan3 {
label = "whr-g301n:green:lan3";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
lan4 {
label = "whr-g301n:green:lan4";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
wan {
label = "whr-g301n:green:wan";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan {
label = "whr-g301n:green:wlan";
gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x3e000>;
label = "u-boot";
read-only;
};
partition@3e000 {
reg = <0x3e000 0x2000>;
label = "u-boot-env";
read-only;
};
partition@40000 {
reg = <0x40000 0x3a0000>;
label = "firmware";
};
partition@3e0000 {
reg = <0x3e0000 0x10000>;
label = "user_property";
read-only;
};
art: partition@3f0000 {
reg = <0x3f0000 0x10000>;
label = "art";
read-only;
};
};
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x120c>;
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x120c>;
mtd-mac-address-increment = <1>;
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
compatible = "pci168c,002a";
reg = <0x0000 0 0 0 0>;
qca,no-eeprom;
mtd-mac-address = <&art 0x120c>;
#gpio-cells = <2>;
gpio-controller;
};
};
&pinmux {
switch_led_pins: switch_led_pins {
pinctrl-single,bits = <0x0 0x0 0xf8>;
};
};
&uart {
status = "okay";
};