mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 23:42:43 +00:00
df8e4b6c2e
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi fast ethernet router, 2.4 GHz single band with two internal antennas. It comes with a horizontal stand black shiny casing. Newer Bright Box 1 model stands vertically, and comes with a totally different board inside, not compatible with this firmware. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 V7.5 @ 320Mhz - RAM: 64 MB DDR2 - Flash: 8 MB SPI NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard) - USB: 1x 2.0 - ADSL: yes, unsupported - Buttons: 2x - LEDs: 9x, power LED is hardware controlled - UART: yes Installation in two steps, new CFE bootloader and firmware: Install new CFE: 1. Power off the router and press the RESET button 2. Power on the router and wait some seconds 3. Release the RESET button 3. Browse to http://192.168.1.1, this web interface will offer both firmware (“Software”) upgrade and bootloader upgrade; be sure to use the bootloader section of the upload form. 4. Upload the new CFE (availabe at the wiki page) 5. Wait about a minute for flashing to finish and reboot into the new bootloader. Install OpenWrt via new CFE web UI: 1. After installing the new CFE, visit http://192.168.1.1 2. Upload the Openwrt cfe firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
187 lines
2.6 KiB
Plaintext
187 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "bcm6328.dtsi"
|
|
|
|
/ {
|
|
model = "Arcadyan AR7516";
|
|
compatible = "arcadyan,ar7516", "brcm,bcm6328";
|
|
|
|
aliases {
|
|
led-failsafe = &led_upgrade_green;
|
|
led-upgrade = &led_upgrade_green;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
bcm43227-sprom {
|
|
compatible = "brcm,bcma-sprom";
|
|
|
|
pci-bus = <1>;
|
|
pci-dev = <0>;
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
|
|
brcm,sprom = "brcm/bcm43227-sprom.bin";
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&hsspi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <16666667>;
|
|
spi-tx-bus-width = <2>;
|
|
spi-rx-bus-width = <2>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
cfe: partition@0 {
|
|
label = "cfe";
|
|
reg = <0x000000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
compatible = "brcm,bcm963xx-imagetag";
|
|
label = "firmware";
|
|
reg = <0x010000 0x7e0000>;
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "nvram";
|
|
reg = <0x7f0000 0x010000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&leds {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_ephy0_act_led &pinctrl_ephy1_act_led
|
|
&pinctrl_ephy2_act_led &pinctrl_ephy3_act_led
|
|
&pinctrl_leds>;
|
|
|
|
led_upgrade_green: led@1 {
|
|
reg = <1>;
|
|
label = "green:upgrade";
|
|
};
|
|
|
|
led@6 {
|
|
reg = <6>;
|
|
active-low;
|
|
label = "green:wan";
|
|
};
|
|
|
|
led@7 {
|
|
reg = <7>;
|
|
active-low;
|
|
label = "green:wifi";
|
|
};
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pinctrl {
|
|
pinctrl_leds: leds {
|
|
function = "led";
|
|
pins = "gpio1", "gpio6", "gpio7";
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
|
|
phy-handle = <&phy1>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
|
|
phy-handle = <&phy2>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
|
|
phy-handle = <&phy3>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "wan";
|
|
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "mii";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh {
|
|
status = "okay";
|
|
};
|
|
|
|
&cfe {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_cfe_6a0: macaddr@6a0 {
|
|
reg = <0x6a0 0x6>;
|
|
};
|
|
};
|