ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
b168a07799
openwrt/target/linux/ath79/image/nand.mk
Chris Blake 949e8ba521 ath79: add support for Netgear PGZNG1 
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.

Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.

Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset

This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.

Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv

2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000

3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin

MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata

Not Working:
Z-Wave
RS422

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-19 12:31:02 +02:00

391 lines
11 KiB
Makefile
Raw Blame History

define Build/dongwon-header
head -c 4 $@ > $@.tmp
head -c 8 /dev/zero >> $@.tmp
tail -c +9 $@ >> $@.tmp
( \
header_crc="$$(head -c 68 $@.tmp | gzip -c | \
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
printf "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
dd of=$@.tmp bs=4 count=1 seek=1 conv=notrunc \
)
mv $@.tmp $@
endef
# attention: only zlib compression is allowed for the boot fs
define Build/zyxel-buildkerneljffs
mkdir -p $@.tmp/boot
cp $@ $@.tmp/boot/vmlinux.lzma.uImage
$(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
--big-endian --squash-uids -v -e 128KiB -q -f -n -x lzma -x rtime \
-o $@ \
-d $@.tmp
rm -rf $@.tmp
endef
define Build/zyxel-factory
let \
maxsize="$(subst k,* 1024,$(RAS_ROOTFS_SIZE))"; \
let size="$$(stat -c%s $@)"; \
if [ $$size -lt $$maxsize ]; then \
$(STAGING_DIR_HOST)/bin/mkrasimage \
-b $(RAS_BOARD) \
-v $(RAS_VERSION) \
-r $@ \
-s $$maxsize \
-o $@.new \
-l 131072 \
&& mv $@.new $@ ; \
fi
endef
define Device/8dev_rambutan
SOC := qca9557
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Rambutan
DEVICE_PACKAGES := kmod-usb2
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
KERNEL_IN_UBI := 1
IMAGES := factory.bin sysupgrade.tar
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
endef
TARGET_DEVICES += 8dev_rambutan
define Device/aerohive_hiveap-121
SOC := ar9344
DEVICE_VENDOR := Aerohive
DEVICE_MODEL := HiveAP 121
DEVICE_PACKAGES := kmod-usb2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 116m
KERNEL_SIZE := 5120k
UBINIZE_OPTS := -E 5
SUPPORTED_DEVICES += hiveap-121
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += aerohive_hiveap-121
define Device/domywifi_dw33d
SOC := qca9558
DEVICE_VENDOR := DomyWifi
DEVICE_MODEL := DW33D
DEVICE_PACKAGES := kmod-usb2 kmod-usb-storage kmod-usb-ledtrig-usbport \
kmod-ath10k-ct ath10k-firmware-qca988x-ct
KERNEL_SIZE := 5120k
IMAGE_SIZE := 98304k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
endef
TARGET_DEVICES += domywifi_dw33d
define Device/dongwon_dw02-412h
SOC := qca9557
DEVICE_VENDOR := Dongwon T&I
DEVICE_MODEL := DW02-412H
DEVICE_ALT0_VENDOR := KT
DEVICE_ALT0_MODEL := GiGA WiFi home
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
KERNEL_SIZE := 8192k
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL := $$(KERNEL) | dongwon-header
KERNEL_INITRAMFS := $$(KERNEL)
UBINIZE_OPTS := -E 5
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/dongwon_dw02-412h-64m
$(Device/dongwon_dw02-412h)
DEVICE_VARIANT := (64M)
DEVICE_ALT0_VARIANT := (64M)
IMAGE_SIZE := 49152k
endef
TARGET_DEVICES += dongwon_dw02-412h-64m
define Device/dongwon_dw02-412h-128m
$(Device/dongwon_dw02-412h)
DEVICE_VARIANT := (128M)
DEVICE_ALT0_VARIANT := (128M)
IMAGE_SIZE := 114688k
endef
TARGET_DEVICES += dongwon_dw02-412h-128m
define Device/glinet_gl-ar300m-common-nand
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR300M
DEVICE_PACKAGES := kmod-usb2
KERNEL_SIZE := 4096k
IMAGE_SIZE := 16000k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
endef
define Device/glinet_gl-ar300m-nand
$(Device/glinet_gl-ar300m-common-nand)
DEVICE_VARIANT := NAND
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
SUPPORTED_DEVICES += glinet,gl-ar300m-nor
endef
TARGET_DEVICES += glinet_gl-ar300m-nand
define Device/glinet_gl-ar300m-nor
$(Device/glinet_gl-ar300m-common-nand)
DEVICE_VARIANT := NOR
SUPPORTED_DEVICES += glinet,gl-ar300m-nand gl-ar300m
endef
TARGET_DEVICES += glinet_gl-ar300m-nor
define Device/glinet_gl-ar750s-common
SOC := qca9563
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750S
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2 \
kmod-usb-storage block-mount
IMAGE_SIZE := 16000k
endef
define Device/glinet_gl-ar750s-nor-nand
$(Device/glinet_gl-ar750s-common)
DEVICE_VARIANT := NOR/NAND
KERNEL_SIZE := 4096k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
SUPPORTED_DEVICES += glinet,gl-ar750s-nor
endef
TARGET_DEVICES += glinet_gl-ar750s-nor-nand
define Device/glinet_gl-ar750s-nor
$(Device/glinet_gl-ar750s-common)
DEVICE_VARIANT := NOR
SUPPORTED_DEVICES += gl-ar750s glinet,gl-ar750s glinet,gl-ar750s-nor-nand
endef
TARGET_DEVICES += glinet_gl-ar750s-nor
define Device/glinet_gl-e750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-E750
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2
SUPPORTED_DEVICES += gl-e750
KERNEL_SIZE := 4096k
IMAGE_SIZE := 131072k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += glinet_gl-e750
define Device/glinet_gl-xe300
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-XE300
DEVICE_PACKAGES := kmod-usb2 block-mount kmod-usb-serial-ch341
KERNEL_SIZE := 4096k
IMAGE_SIZE := 131072k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += glinet_gl-xe300
# fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff)
define Device/netgear_ath79_nand
DEVICE_VENDOR := NETGEAR
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
KERNEL_SIZE := 4096k
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 25600k
KERNEL := kernel-bin | append-dtb | lzma -d20 | \
pad-offset $$(KERNEL_SIZE) 129 | uImage lzma | \
append-string -e '\xff' | \
append-uImage-fakehdr filesystem $$(UIMAGE_MAGIC)
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma -d20 | uImage lzma
IMAGES := sysupgrade.bin factory.img
IMAGE/factory.img := append-kernel | append-ubi | netgear-dni | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
UBINIZE_OPTS := -E 5
endef
define Device/netgear_pgzng1
SOC := ar9344
DEVICE_MODEL := PGZNG1
DEVICE_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := Pulse Gateway
DEVICE_ALT0_VENDOR := ADT
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-i2c-gpio \
kmod-leds-pca955x kmod-rtc-isl1208 kmod-spi-dev
KERNEL_SIZE := 5120k
IMAGE_SIZE := 83968k
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
endef
TARGET_DEVICES += netgear_pgzng1
define Device/netgear_r6100
SOC := ar9344
DEVICE_MODEL := R6100
UIMAGE_MAGIC := 0x36303030
NETGEAR_BOARD_ID := R6100
NETGEAR_HW_ID := 29764434+0+128+128+2x2+2x2
$(Device/netgear_ath79_nand)
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r6100
define Device/netgear_wndr3700-v4
SOC := ar9344
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v4
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR3700v4
NETGEAR_HW_ID := 29763948+128+128
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr3700-v4
define Device/netgear_wndr4300
SOC := ar9344
DEVICE_MODEL := WNDR4300
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300
define Device/netgear_wndr4300sw
SOC := ar9344
DEVICE_MODEL := WNDR4300SW
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300SW
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300sw
define Device/netgear_wndr4300tn
SOC := ar9344
DEVICE_MODEL := WNDR4300TN
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300TN
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300tn
define Device/netgear_wndr4300-v2
SOC := qca9563
DEVICE_MODEL := WNDR4300
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := WNDR4500series
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012175
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300-v2
define Device/netgear_wndr4500-v3
SOC := qca9563
DEVICE_MODEL := WNDR4500
DEVICE_VARIANT := v3
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := WNDR4500series
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4500-v3
define Device/zte_mf286_common
SOC := qca9563
DEVICE_VENDOR := ZTE
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/zte_mf286
$(Device/zte_mf286_common)
DEVICE_MODEL := MF286
DEVICE_PACKAGES += ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan \
kmod-usb-serial-option uqmi
endef
TARGET_DEVICES += zte_mf286
define Device/zte_mf286a
$(Device/zte_mf286_common)
DEVICE_MODEL := MF286A
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan \
kmod-usb-serial-option uqmi
endef
TARGET_DEVICES += zte_mf286a
define Device/zte_mf286r
$(Device/zte_mf286_common)
DEVICE_MODEL := MF286R
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis kmod-usb-acm \
comgt-ncm
endef
TARGET_DEVICES += zte_mf286r
define Device/zyxel_nbg6716
SOC := qca9558
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6716
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \
ath10k-firmware-qca988x-ct
RAS_BOARD := NBG6716
RAS_ROOTFS_SIZE := 29696k
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
KERNEL_SIZE := 4096k
BLOCKSIZE := 128k
PAGESIZE := 2048
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none | \
zyxel-buildkerneljffs | check-size 4096k
IMAGES := sysupgrade.tar sysupgrade-4M-Kernel.bin factory.bin
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
IMAGE/sysupgrade-4M-Kernel.bin/squashfs := append-kernel | \
pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to 263192576 | gzip
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
zyxel-factory
UBINIZE_OPTS := -E 5
endef
TARGET_DEVICES += zyxel_nbg6716
define Device/zyxel_emg2926_q10a
$(Device/zyxel_nbg6716)
DEVICE_MODEL := EMG2926-Q10A
RAS_BOARD := AAVK-EMG2926Q10A
endef
TARGET_DEVICES += zyxel_emg2926_q10a
Reference in New Issue View Git Blame Copy Permalink