mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-24 07:46:48 +00:00
635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
144 lines
2.2 KiB
Plaintext
144 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
compatible = "engenius,ecb1750", "qca,qca9558";
|
|
model = "EnGenius ECB1750";
|
|
|
|
aliases {
|
|
led-boot = &led_power_orange;
|
|
led-failsafe = &led_power_orange;
|
|
led-running = &led_power_orange;
|
|
led-upgrade = &led_power_orange;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_orange: power_orange {
|
|
label = "ecb1750:orange:power";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "ecb1750:blue:wlan2g";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wlan5g {
|
|
label = "ecb1750:blue:wlan5g";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "ecb1750:blue:lan";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0xf50000>;
|
|
};
|
|
|
|
partition@fa0000 {
|
|
label = "userconfig";
|
|
reg = <0xfa0000 0x050000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
eee-broken-100tx;
|
|
eee-broken-1000t;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x9a000000 0x80000101 0x80001313>;
|
|
|
|
phy-handle = <&phy5>;
|
|
phy-mode = "rgmii";
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
rgmii-gmac0 = <1>;
|
|
rxd-delay = <3>;
|
|
rxdv-delay = <3>;
|
|
};
|
|
};
|