mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 08:21:14 +00:00
d9ab3240a5
Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
127 lines
2.1 KiB
Diff
127 lines
2.1 KiB
Diff
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
@@ -67,9 +67,23 @@
|
|
};
|
|
};
|
|
|
|
- dsa {
|
|
- status = "disabled";
|
|
+ switches {
|
|
+ #address-cells = <1>;
|
|
+ #size-cells = <0>;
|
|
|
|
+ mvsw61xx@10 {
|
|
+ compatible = "marvell,88e6171";
|
|
+ status = "okay";
|
|
+ reg = <0x10>;
|
|
+
|
|
+ mii-bus = <&mdio>;
|
|
+ cpu-port-0 = <5>;
|
|
+ cpu-port-1 = <6>;
|
|
+ is-indirect;
|
|
+ };
|
|
+ };
|
|
+
|
|
+ dsa {
|
|
compatible = "marvell,dsa";
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
@@ -161,22 +175,22 @@
|
|
};
|
|
|
|
partition@200000 {
|
|
- label = "kernel";
|
|
+ label = "kernel1";
|
|
reg = <0x200000 0x2A0000>;
|
|
};
|
|
|
|
partition@4a0000 {
|
|
- label = "rootfs";
|
|
+ label = "rootfs1";
|
|
reg = <0x4A0000 0x1760000>;
|
|
};
|
|
|
|
partition@1c00000 {
|
|
- label = "alt_kernel";
|
|
+ label = "kernel2";
|
|
reg = <0x1C00000 0x2A0000>;
|
|
};
|
|
|
|
partition@1ea0000 {
|
|
- label = "alt_rootfs";
|
|
+ label = "rootfs2";
|
|
reg = <0x1EA0000 0x1760000>;
|
|
};
|
|
|
|
@@ -207,53 +221,6 @@
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
-
|
|
- switch@10 {
|
|
- compatible = "marvell,mv88e6085";
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
- reg = <16>;
|
|
-
|
|
- ports {
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
-
|
|
- port@0 {
|
|
- reg = <0>;
|
|
- label = "ethernet1";
|
|
- };
|
|
-
|
|
- port@1 {
|
|
- reg = <1>;
|
|
- label = "ethernet2";
|
|
- };
|
|
-
|
|
- port@2 {
|
|
- reg = <2>;
|
|
- label = "ethernet3";
|
|
- };
|
|
-
|
|
- port@3 {
|
|
- reg = <3>;
|
|
- label = "ethernet4";
|
|
- };
|
|
-
|
|
- port@4 {
|
|
- reg = <4>;
|
|
- label = "internet";
|
|
- };
|
|
-
|
|
- port@5 {
|
|
- reg = <5>;
|
|
- label = "cpu";
|
|
- ethernet = <ð0port>;
|
|
- fixed-link {
|
|
- speed = <1000>;
|
|
- full-duplex;
|
|
- };
|
|
- };
|
|
- };
|
|
- };
|
|
};
|
|
|
|
&uart0 {
|
|
@@ -272,10 +239,14 @@
|
|
};
|
|
|
|
/* eth1 is connected to the switch at port 6. However DSA only supports a
|
|
- * single CPU port. So leave this port disabled to avoid confusion.
|
|
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
|
|
*/
|
|
ð1 {
|
|
- status = "disabled";
|
|
+ status = "okay";
|
|
+ ethernet1-port@0 {
|
|
+ speed = <1000>;
|
|
+ duplex = <1>;
|
|
+ };
|
|
};
|
|
|
|
/* There is no battery on the board, so the RTC does not keep
|