openwrt/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
Christoph Krapp af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:20 +01:00

165 lines
3.9 KiB
Bash

#!/bin/sh
. /lib/functions/k2t.sh
# xor multiple hex values of the same length
xor() {
local val
local ret="0x$1"
local retlen=${#1}
shift
while [ -n "$1" ]; do
val="0x$1"
ret=$((ret ^ val))
shift
done
printf "%0${retlen}x" "$ret"
}
ath10kcal_die() {
echo "ath10cal: " "$*"
exit 1
}
ath10kcal_from_file() {
local source=$1
local offset=$2
local count=$3
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $source"
}
ath10kcal_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath10kcal_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $mtd"
}
ath10kcal_patch_mac() {
local mac=$1
[ -z "$mac" ] && return
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
}
ath10kcal_patch_mac_crc() {
local mac=$1
local mac_offset=6
local chksum_offset=2
local xor_mac
local xor_fw_mac
local xor_fw_chksum
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
ath10kcal_patch_mac "$mac" && {
xor_mac=${mac//:/}
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
}
}
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions.sh
. /lib/functions/system.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
devolo,dvl1200e|\
devolo,dvl1750c)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
;;
dlink,dir-859-a1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
;;
glinet,ar750s|\
tplink,re450-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
glinet,gl-x750)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
nec,wg800hp)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
;;
ocedo,koala)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
;;
openmesh,om5p-ac-v2)
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
tplink,archer-c7-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
;;
tplink,archer-a7-v5|\
tplink,archer-c7-v5)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
;;
ubnt,unifiac-lite|\
ubnt,unifiac-mesh|\
ubnt,unifiac-mesh-pro|\
ubnt,lap-120|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,unifiac-pro)
ath10kcal_extract "EEPROM" 20480 2116
;;
esac
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
tplink,archer-c58-v1|\
tplink,archer-c59-v1)
ath10kcal_extract "art" 20480 12064
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
esac
;;
*)
exit 1
;;
esac