mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
88ca6390ea
Refresh patches on all 4.4 supported platforms. Compile & run tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
106 lines
3.4 KiB
Diff
106 lines
3.4 KiB
Diff
From a4be9046c3a3fc39a06089553df8cc19a2abd814 Mon Sep 17 00:00:00 2001
|
|
From: Priyanka Jain <Priyanka.Jain@freescale.com>
|
|
Date: Tue, 3 Nov 2015 11:25:24 +0530
|
|
Subject: [PATCH 233/238] i2c: pca954x: Add option to skip disabling PCA954x
|
|
Mux device
|
|
|
|
On some Layerscape boards like LS2085ARDB/LS2080ARDB,
|
|
input pull-up resistors on PCA954x Mux device are
|
|
missing on board. So, if mux are disabled after powered-on,
|
|
input lines will float leading to incorrect functionality.
|
|
|
|
Hence, PCA954x Mux device should never be turned-off after
|
|
power-on.
|
|
|
|
Add option to skip disabling PCA954x Mux device
|
|
if device tree contians "i2c-mux-never-disable" property
|
|
for pca954x device node.
|
|
|
|
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
|
|
---
|
|
drivers/i2c/muxes/i2c-mux-pca954x.c | 38 +++++++++++++++++++++++++++++++++++
|
|
1 file changed, 38 insertions(+)
|
|
|
|
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
|
|
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
|
|
@@ -63,6 +63,7 @@ struct pca954x {
|
|
struct i2c_adapter *virt_adaps[PCA954X_MAX_NCHANS];
|
|
|
|
u8 last_chan; /* last register value */
|
|
+ u8 disable_mux; /* do not disable mux if val not 0 */
|
|
};
|
|
|
|
struct chip_desc {
|
|
@@ -174,6 +175,13 @@ static int pca954x_deselect_mux(struct i
|
|
{
|
|
struct pca954x *data = i2c_get_clientdata(client);
|
|
|
|
+#ifdef CONFIG_ARCH_LAYERSCAPE
|
|
+ if (data->disable_mux != 0)
|
|
+ data->last_chan = chips[data->type].nchans;
|
|
+ else
|
|
+ data->last_chan = 0;
|
|
+ return pca954x_reg_write(adap, client, data->disable_mux);
|
|
+#endif
|
|
/* Deselect active channel */
|
|
data->last_chan = 0;
|
|
return pca954x_reg_write(adap, client, data->last_chan);
|
|
@@ -201,6 +209,23 @@ static int pca954x_probe(struct i2c_clie
|
|
if (!data)
|
|
return -ENOMEM;
|
|
|
|
+#ifdef CONFIG_ARCH_LAYERSCAPE
|
|
+ /* The point here is that you must not disable a mux if there
|
|
+ * are no pullups on the input or you mess up the I2C. This
|
|
+ * needs to be put into the DTS really as the kernel cannot
|
|
+ * know this otherwise.
|
|
+ */
|
|
+ data->type = id->driver_data;
|
|
+ data->disable_mux = of_node &&
|
|
+ of_property_read_bool(of_node, "i2c-mux-never-disable") &&
|
|
+ chips[data->type].muxtype == pca954x_ismux ?
|
|
+ chips[data->type].enable : 0;
|
|
+ /* force the first selection */
|
|
+ if (data->disable_mux != 0)
|
|
+ data->last_chan = chips[data->type].nchans;
|
|
+ else
|
|
+ data->last_chan = 0;
|
|
+#endif
|
|
i2c_set_clientdata(client, data);
|
|
|
|
/* Get the mux out of reset if a reset GPIO is specified. */
|
|
@@ -212,13 +237,19 @@ static int pca954x_probe(struct i2c_clie
|
|
* that the mux is in fact present. This also
|
|
* initializes the mux to disconnected state.
|
|
*/
|
|
+#ifdef CONFIG_ARCH_LAYERSCAPE
|
|
+ if (i2c_smbus_write_byte(client, data->disable_mux) < 0) {
|
|
+#else
|
|
if (i2c_smbus_write_byte(client, 0) < 0) {
|
|
+#endif
|
|
dev_warn(&client->dev, "probe failed\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
+#ifndef CONFIG_ARCH_LAYERSCAPE
|
|
data->type = id->driver_data;
|
|
data->last_chan = 0; /* force the first selection */
|
|
+#endif
|
|
|
|
idle_disconnect_dt = of_node &&
|
|
of_property_read_bool(of_node, "i2c-mux-idle-disconnect");
|
|
@@ -289,6 +320,13 @@ static int pca954x_resume(struct device
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct pca954x *data = i2c_get_clientdata(client);
|
|
|
|
+#ifdef CONFIG_ARCH_LAYERSCAPE
|
|
+ if (data->disable_mux != 0)
|
|
+ data->last_chan = chips[data->type].nchans;
|
|
+ else
|
|
+ data->last_chan = 0;
|
|
+ return i2c_smbus_write_byte(client, data->disable_mux);
|
|
+#endif
|
|
data->last_chan = 0;
|
|
return i2c_smbus_write_byte(client, 0);
|
|
}
|