mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 16:31:13 +00:00
fce21ae4cc
Right now all brcm2708 patches are extracted from the non-mainline raspberrypi/linux git tree. Many of them are hacks and/or are unneeded in LEDE. Raspberry Pi is getting better and better mainline support so it would be nice to finally start maintaining patches in a cleaner way: 1) Backport patches accepted in upstream tree 2) Start using upstream drivers 3) Pick only these patches that are needed for more complete support Handling above tasks requires grouping patches - ideally using the same prefixes as generic ones. It means we should rename existing patches to use some high prefix. This will allow e.g. use 0xx for backported code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
87 lines
2.5 KiB
Diff
87 lines
2.5 KiB
Diff
From 0360d687752df3c5546dd1534904a6e0168b6360 Mon Sep 17 00:00:00 2001
|
|
From: Phil Elwell <phil@raspberrypi.org>
|
|
Date: Wed, 1 Mar 2017 16:07:39 +0000
|
|
Subject: [PATCH] amba_pl011: Round input clock up
|
|
|
|
The UART clock is initialised to be as close to the requested
|
|
frequency as possible without exceeding it. Now that there is a
|
|
clock manager that returns the actual frequencies, an expected
|
|
48MHz clock is reported as 47999625. If the requested baudrate
|
|
== requested clock/16, there is no headroom and the slight
|
|
reduction in actual clock rate results in failure.
|
|
|
|
Detect cases where it looks like a "round" clock was chosen and
|
|
adjust the reported clock to match that "round" value. As the
|
|
code comment says:
|
|
|
|
/*
|
|
* If increasing a clock by less than 0.1% changes it
|
|
* from ..999.. to ..000.., round up.
|
|
*/
|
|
|
|
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
|
|
---
|
|
drivers/tty/serial/amba-pl011.c | 23 +++++++++++++++++++++--
|
|
1 file changed, 21 insertions(+), 2 deletions(-)
|
|
|
|
--- a/drivers/tty/serial/amba-pl011.c
|
|
+++ b/drivers/tty/serial/amba-pl011.c
|
|
@@ -1646,6 +1646,23 @@ static void pl011_put_poll_char(struct u
|
|
|
|
#endif /* CONFIG_CONSOLE_POLL */
|
|
|
|
+unsigned long pl011_clk_round(unsigned long clk)
|
|
+{
|
|
+ unsigned long scaler;
|
|
+
|
|
+ /*
|
|
+ * If increasing a clock by less than 0.1% changes it
|
|
+ * from ..999.. to ..000.., round up.
|
|
+ */
|
|
+ scaler = 1;
|
|
+ while (scaler * 100000 < clk)
|
|
+ scaler *= 10;
|
|
+ if ((clk + scaler - 1)/scaler % 1000 == 0)
|
|
+ clk = (clk/scaler + 1) * scaler;
|
|
+
|
|
+ return clk;
|
|
+}
|
|
+
|
|
static int pl011_hwinit(struct uart_port *port)
|
|
{
|
|
struct uart_amba_port *uap =
|
|
@@ -1662,7 +1679,7 @@ static int pl011_hwinit(struct uart_port
|
|
if (retval)
|
|
return retval;
|
|
|
|
- uap->port.uartclk = clk_get_rate(uap->clk);
|
|
+ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk));
|
|
|
|
/* Clear pending error and receive interrupts */
|
|
pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
|
|
@@ -2300,7 +2317,7 @@ static int __init pl011_console_setup(st
|
|
plat->init();
|
|
}
|
|
|
|
- uap->port.uartclk = clk_get_rate(uap->clk);
|
|
+ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk));
|
|
|
|
if (uap->vendor->fixed_options) {
|
|
baud = uap->fixed_baud;
|
|
@@ -2372,6 +2389,7 @@ static struct uart_driver amba_reg = {
|
|
.cons = AMBA_CONSOLE,
|
|
};
|
|
|
|
+#if 0
|
|
static int pl011_probe_dt_alias(int index, struct device *dev)
|
|
{
|
|
struct device_node *np;
|
|
@@ -2403,6 +2421,7 @@ static int pl011_probe_dt_alias(int inde
|
|
|
|
return ret;
|
|
}
|
|
+#endif
|
|
|
|
/* unregisters the driver also if no more ports are left */
|
|
static void pl011_unregister_port(struct uart_amba_port *uap)
|