mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
c12ef2f760
Specs (same as in v1): - MT7628AN (575 MHz) - 64MB RAM - 8MB of flash (SPI NOR) - 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan) - 1x 2.4GHz wifi (MT7628AN) - 1x 5Ghz wifi (MT7612E) - 4x LEDs (5 GPIO-controlled) - 1x reset button - 1x WPS button The only and important difference between v1 & v3 is in flash memory layout, so pls don't interchange these 2 builds! Installation through web-ui (on OEM factory firmware): 1. Visit http://tplinkrepeater.net or the configured IP address of your RE305 v3 (default 192.168.0.254). 2. Log in with the password you've set during initial setup of the RE305 (there is no default password). 3. Go to Settings -> System Tools -> Firmware upgrade 4. Click Browse and select the OpenWRT image with factory.bin suffix (not sysupgrade.bin) 5. A window with a progress bar will appear. Wait until it completes. 6. The RE305 will reboot into OpenWRT and serve DHCP requests on the ethernet port. 7. Connect an RJ45 cable from the RE305 to your computer and access LuCI at http://192.168.1.1/ to configure (or use ssh). Disassembly: Just unscrew 4 screws in the corners & take off the back cover. Serial is exposed to the right side of the main board (in the middle) and marked with TX/RX/3V3/GND, but the holes are filled with solder. Installation through serial: 1. connect trough serial (1n8, baudrate=57600) 2. setup the TFTP server and connect it via ethernet (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc) 3. boot from a initramfs image first (choose 1 in the bootloader options) 4. test it a bit with that, then proceed to run sysupgrade build MAC addresses as verified by OEM firmware: use OpenWrt address reference LAN eth0 *:d2 label 2g wlan0 *:d1 label - 1 5g wlan1 *:d0 label - 2 The label MAC address can be found in config 0x2008. Signed-off-by: Michal Kozuch <servitkar@gmail.com> [redistribute WLAN node properties between DTS/DTSI, remove compatible on DTSI, fix indent/wrapping, split out firmware-utils change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
80 lines
1.4 KiB
Plaintext
80 lines
1.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7628an_tplink_re305.dtsi"
|
|
|
|
/ {
|
|
compatible = "tplink,re305-v3", "mediatek,mt7628an-soc";
|
|
model = "TP-Link RE305 v3";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
label = "firmware";
|
|
reg = <0x20000 0x7a0000>;
|
|
};
|
|
|
|
config: partition@7c0000 {
|
|
label = "config";
|
|
reg = <0x7c0000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
radio: partition@7f0000 {
|
|
label = "radio";
|
|
reg = <0x7f0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wlan5g {
|
|
mediatek,mtd-eeprom = <&radio 0x8000>;
|
|
|
|
nvmem-cells = <&macaddr_config_2008>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <(-2)>;
|
|
};
|
|
|
|
&wmac {
|
|
mediatek,mtd-eeprom = <&radio 0x0>;
|
|
|
|
nvmem-cells = <&macaddr_config_2008>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
ðernet {
|
|
nvmem-cells = <&macaddr_config_2008>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&config {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_config_2008: macaddr@2008 {
|
|
reg = <0x2008 0x6>;
|
|
};
|
|
};
|