openwrt/target/linux/ramips/dts/mt7621_tplink_re650-v2.dts
Marcin Gordziejewski 39799974a3 ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
  requires soldering because they're not through holes.

  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.

Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-23 22:02:27 +02:00

196 lines
3.3 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "tplink,re650-v2", "mediatek,mt7621-soc";
model = "TP-Link RE650 v2";
aliases {
label-mac-device = &gmac0;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_WPS_BUTTON>;
};
power {
label = "power";
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_POWER>;
};
led {
label = "led";
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_LIGHTS_TOGGLE>;
};
reset {
label = "reset";
gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "blue:power";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
};
wifi2g {
label = "blue:wifi2g";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wifi5g {
label = "blue:wifi5g";
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wps_red {
label = "red:wps";
gpios = <&gpio 26 GPIO_ACTIVE_HIGH>;
};
wps_blue {
label = "blue:wps";
gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
};
eth_act {
label = "green:eth_act";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
};
eth_link {
label = "green:eth_link";
gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x20000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x20000 0x7a0000>;
};
config: partition@7c0000 {
label = "config";
reg = <0x7c0000 0x2d440>;
read-only;
};
radio: partition@7f0000 {
label = "radio";
reg = <0x7f0000 0x10000>;
read-only;
};
};
};
};
&state_default {
gpio {
groups = "rgmii2", "wdt";
function = "gpio";
};
};
&pcie {
status = "okay";
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&radio 0x0>;
nvmem-cells = <&macaddr_config_10008>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&radio 0x8000>;
nvmem-cells = <&macaddr_config_10008>;
nvmem-cell-names = "mac-address";
mac-address-increment = <2>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&ethernet {
pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>;
};
&gmac0 {
nvmem-cells = <&macaddr_config_10008>;
nvmem-cell-names = "mac-address";
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan";
};
};
};
&config {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_config_10008: macaddr@10008 {
reg = <0x10008 0x6>;
};
};