mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 02:29:01 +00:00
b4184c666c
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
90 lines
2.7 KiB
Diff
90 lines
2.7 KiB
Diff
From a10fab12a927e60b7141a602e740d70cb4d09e4a Mon Sep 17 00:00:00 2001
|
|
From: John Crispin <john@phrozen.org>
|
|
Date: Thu, 9 Mar 2017 11:03:18 +0100
|
|
Subject: [PATCH] arm: boot: add dts files
|
|
|
|
Signed-off-by: John Crispin <john@phrozen.org>
|
|
---
|
|
arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
|
|
1 file changed, 23 insertions(+)
|
|
|
|
--- a/arch/arm/boot/dts/Makefile
|
|
+++ b/arch/arm/boot/dts/Makefile
|
|
@@ -951,11 +951,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
|
qcom-ipq4018-ap120c-ac.dtb \
|
|
qcom-ipq4018-ap120c-ac-bit.dtb \
|
|
qcom-ipq4018-jalapeno.dtb \
|
|
+ qcom-ipq4018-a42.dtb \
|
|
+ qcom-ipq4018-ap120c-ac.dtb \
|
|
+ qcom-ipq4018-dap-2610.dtb \
|
|
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
|
|
+ qcom-ipq4018-magic-2-wifi-next.dtb \
|
|
+ qcom-ipq4018-ea6350v3.dtb \
|
|
+ qcom-ipq4018-eap1300.dtb \
|
|
+ qcom-ipq4018-ecw5211.dtb \
|
|
+ qcom-ipq4018-emd1.dtb \
|
|
+ qcom-ipq4018-emr3500.dtb \
|
|
+ qcom-ipq4018-ens620ext.dtb \
|
|
+ qcom-ipq4018-ex6100v2.dtb \
|
|
+ qcom-ipq4018-ex6150v2.dtb \
|
|
+ qcom-ipq4018-fritzbox-4040.dtb \
|
|
+ qcom-ipq4018-gl-ap1300.dtb \
|
|
+ qcom-ipq4018-meshpoint-one.dtb \
|
|
+ qcom-ipq4018-cap-ac.dtb \
|
|
+ qcom-ipq4018-hap-ac2.dtb \
|
|
+ qcom-ipq4018-sxtsq-5-ac.dtb \
|
|
+ qcom-ipq4018-nbg6617.dtb \
|
|
+ qcom-ipq4019-oap100.dtb \
|
|
+ qcom-ipq4018-pa1200.dtb \
|
|
+ qcom-ipq4018-rt-ac58u.dtb \
|
|
+ qcom-ipq4018-rutx10.dtb \
|
|
+ qcom-ipq4018-wac510.dtb \
|
|
+ qcom-ipq4018-whw01-v1.dtb \
|
|
+ qcom-ipq4018-wre6606.dtb \
|
|
+ qcom-ipq4018-wrtq-329acn.dtb \
|
|
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk04.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk04.1-c3.dtb \
|
|
qcom-ipq4019-ap.dk07.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
|
+ qcom-ipq4019-a62.dtb \
|
|
+ qcom-ipq4019-cm520-79f.dtb \
|
|
+ qcom-ipq4019-e2600ac-c1.dtb \
|
|
+ qcom-ipq4019-e2600ac-c2.dtb \
|
|
+ qcom-ipq4019-ea8300.dtb \
|
|
+ qcom-ipq4019-eap2200.dtb \
|
|
+ qcom-ipq4019-fritzbox-7530.dtb \
|
|
+ qcom-ipq4019-fritzrepeater-1200.dtb \
|
|
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
|
+ qcom-ipq4019-habanero-dvk.dtb \
|
|
+ qcom-ipq4019-hap-ac3.dtb \
|
|
+ qcom-ipq4019-map-ac2200.dtb \
|
|
+ qcom-ipq4019-lhgg-60ad.dtb \
|
|
+ qcom-ipq4019-mf286d.dtb \
|
|
+ qcom-ipq4019-mr8300.dtb \
|
|
+ qcom-ipq4019-pa2200.dtb \
|
|
+ qcom-ipq4019-r619ac-64m.dtb \
|
|
+ qcom-ipq4019-r619ac-128m.dtb \
|
|
+ qcom-ipq4019-rbr50.dtb \
|
|
+ qcom-ipq4019-rbs50.dtb \
|
|
+ qcom-ipq4019-rt-ac42u.dtb \
|
|
+ qcom-ipq4019-rtl30vw.dtb \
|
|
+ qcom-ipq4019-srr60.dtb \
|
|
+ qcom-ipq4019-srs60.dtb \
|
|
+ qcom-ipq4019-u4019-32m.dtb \
|
|
+ qcom-ipq4019-wifi.dtb \
|
|
+ qcom-ipq4019-wpj419.dtb \
|
|
+ qcom-ipq4019-wtr-m2133hp.dtb \
|
|
+ qcom-ipq4019-x1pro.dtb \
|
|
+ qcom-ipq4028-wpj428.dtb \
|
|
+ qcom-ipq4029-ap-303.dtb \
|
|
+ qcom-ipq4029-ap-303h.dtb \
|
|
+ qcom-ipq4029-ap-365.dtb \
|
|
+ qcom-ipq4029-gl-b1300.dtb \
|
|
+ qcom-ipq4019-gl-b2200.dtb \
|
|
+ qcom-ipq4029-gl-s1300.dtb \
|
|
+ qcom-ipq4029-mr33.dtb \
|
|
qcom-ipq8064-ap148.dtb \
|
|
qcom-ipq8064-rb3011.dtb \
|
|
qcom-msm8226-samsung-s3ve3g.dtb \
|