mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 01:59:02 +00:00
9715beb04c
This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves support for the EdgeRouter X (PoE-passthrough). Specification: - SoC: MediaTek MT7621AT - Flash: 256 MiB - RAM: 265 MiB - Ethernet: 5 x LAN (1000 Mbps) - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1 - EdgeRouter X: - 1 x PoE-Passtrough (Eth4) - powered by Wallwart or passive PoE - EdgeRouter X-SFP: - 5 x PoE-Out (24V, passive) - 1 x SFP (unknown status) - powered by Wallwart (24V) Doesn't work: * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. Installation via vendor firmware: - build an Initrd-image (> 3MiB) and upload the factory-image - initrd can have luci-mod-failsafe - flash final firmware via LuCI / sysupgrade on rebooted system via TFTP: - stop uboot into tftp-load into option "1" - upload factory.bin image Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
107 lines
1.7 KiB
Plaintext
107 lines
1.7 KiB
Plaintext
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "ubiquiti,edgerouterx";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x10000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x22>;
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "u-boot-env";
|
|
reg = <0x80000 0x60000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@e0000 {
|
|
label = "factory";
|
|
reg = <0xe0000 0x60000>;
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "kernel1";
|
|
reg = <0x140000 0x300000>;
|
|
};
|
|
|
|
partition@440000 {
|
|
label = "kernel2";
|
|
reg = <0x440000 0x300000>;
|
|
};
|
|
|
|
partition@740000 {
|
|
label = "ubi";
|
|
reg = <0x740000 0xf7c0000>;
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "uart2", "uart3", "i2c", "pcie", "rgmii2", "jtag";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
/* This board has 2Mb spi flash soldered in and visible
|
|
from manufacturer's firmware.
|
|
But this SoC shares spi and nand pins,
|
|
and current driver does't handle this sharing well */
|
|
status = "disabled";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <1>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "spi";
|
|
reg = <0x0 0x200000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
&xhci {
|
|
status = "disabled";
|
|
};
|