mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
3c0e2aa63e
I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
141 lines
2.1 KiB
Plaintext
141 lines
2.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "iodata:green:wps";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_power: power {
|
|
label = "iodata:green:power";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
repeater {
|
|
label = "repeater";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
partitions: partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "u-boot-env";
|
|
reg = <0x0100000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@200000 {
|
|
label = "factory";
|
|
reg = <0x0200000 0x0100000>;
|
|
};
|
|
|
|
partition@300000 {
|
|
label = "SecondBoot";
|
|
reg = <0x0300000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@400000 {
|
|
label = "kernel";
|
|
reg = <0x0400000 0x0400000>;
|
|
};
|
|
|
|
partition@800000 {
|
|
label = "ubi";
|
|
reg = <0x0800000 0x2e00000>;
|
|
};
|
|
|
|
partition@3600000 {
|
|
label = "Config";
|
|
reg = <0x3600000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3700000 {
|
|
label = "firmware_2";
|
|
reg = <0x3700000 0x3200000>;
|
|
};
|
|
|
|
partition@6900000 {
|
|
label = "Config_2";
|
|
reg = <0x6900000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@6a00000 {
|
|
label = "persist";
|
|
reg = <0x6a00000 0x0100000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0xe000>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
ralink,group = "uart2", "uart3", "wdt";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
|
|
&xhci {
|
|
status = "disabled";
|
|
};
|