mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
a9071d02b5
The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
126 lines
2.5 KiB
Bash
126 lines
2.5 KiB
Bash
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
platform_check_image() {
|
|
case "$(board_name)" in
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
local ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
local asus_root=$(nand_find_volume $ubidev jffs2)
|
|
|
|
[ -n "$asus_root" ] || return 0
|
|
|
|
cat << EOF
|
|
jffs2 partition is still present.
|
|
There's probably no space left
|
|
to install the filesystem.
|
|
|
|
You need to delete the jffs2 partition first:
|
|
# ubirmvol /dev/ubi0 --name=jffs2
|
|
|
|
Once this is done. Retry.
|
|
EOF
|
|
return 1
|
|
;;
|
|
esac
|
|
return 0;
|
|
}
|
|
|
|
askey_do_upgrade() {
|
|
local tar_file="$1"
|
|
|
|
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
|
board_dir=${board_dir%/}
|
|
|
|
tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs
|
|
|
|
nand_do_upgrade "$1"
|
|
}
|
|
|
|
zyxel_do_upgrade() {
|
|
local tar_file="$1"
|
|
|
|
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
|
board_dir=${board_dir%/}
|
|
|
|
tar Oxf $tar_file ${board_dir}/kernel | mtd write - kernel
|
|
|
|
if [ -n "$UPGRADE_BACKUP" ]; then
|
|
tar Oxf $tar_file ${board_dir}/root | mtd -j "$UPGRADE_BACKUP" write - rootfs
|
|
else
|
|
tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs
|
|
fi
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
case "$(board_name)" in
|
|
8dev,jalapeno |\
|
|
aruba,ap-303 |\
|
|
aruba,ap-303h |\
|
|
aruba,ap-365 |\
|
|
avm,fritzbox-7530 |\
|
|
avm,fritzrepeater-1200 |\
|
|
avm,fritzrepeater-3000 |\
|
|
buffalo,wtr-m2133hp |\
|
|
cilab,meshpoint-one |\
|
|
edgecore,ecw5211 |\
|
|
edgecore,oap100 |\
|
|
engenius,eap2200 |\
|
|
luma,wrtq-329acn |\
|
|
mobipromo,cm520-79f |\
|
|
qxwlan,e2600ac-c2)
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
alfa-network,ap120c-ac)
|
|
part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
|
|
if [ "$part" = "rootfs1" ]; then
|
|
fw_setenv active 2 || exit 1
|
|
CI_UBIPART="rootfs2"
|
|
else
|
|
fw_setenv active 1 || exit 1
|
|
CI_UBIPART="rootfs1"
|
|
fi
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
asus,map-ac2200)
|
|
CI_KERNPART="linux"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
CI_KERNPART="linux"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
cellc,rtl30vw)
|
|
CI_UBIPART="ubifs"
|
|
askey_do_upgrade "$1"
|
|
;;
|
|
compex,wpj419)
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
linksys,ea6350v3 |\
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
platform_do_upgrade_linksys "$1"
|
|
;;
|
|
meraki,mr33)
|
|
CI_KERNPART="part.safe"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_openmesh "$1"
|
|
;;
|
|
zyxel,nbg6617)
|
|
zyxel_do_upgrade "$1"
|
|
;;
|
|
*)
|
|
default_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|