openwrt/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
Hans Geiblinger a9071d02b5 ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:31:51 +02:00

248 lines
8.1 KiB
Bash

#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions/caldata.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:01:00.0.bin")
case "$board" in
meraki,mr33)
caldata_extract_ubi "ART" 0x9000 0x844
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +1)
;;
esac
;;
"ath10k/pre-cal-pci-0000:01:00.0.bin")
case "$board" in
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x9000 0x2f20
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x9000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
;;
engenius,eap2200 |\
openmesh,a62)
caldata_extract "0:ART" 0x9000 0x2f20
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x9000 0x2f20
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;;
esac
;;
"ath10k/pre-cal-ahb-a000000.wifi.bin")
case "$board" in
8dev,habanero-dvk |\
8dev,jalapeno |\
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x1000 0x2f20
;;
aruba,ap-303 |\
aruba,ap-303h |\
aruba,ap-365)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary mfginfo 0x1D)
;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x26)
;;
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
edgecore,ecw5211 |\
edgecore,oap100 |\
engenius,eap1300 |\
engenius,eap2200 |\
luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
caldata_extract "0:ART" 0x1000 0x2f20
;;
dlink,dap-2610)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
;;
engenius,emd1)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
;;
engenius,emr3500)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
;;
engenius,ens620ext)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
;;
meraki,mr33)
caldata_extract_ubi "ART" 0x1000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +2)
;;
netgear,ex6100v2 |\
netgear,ex6150v2)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0)
;;
zyxel,nbg6617 |\
zyxel,wre6606)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
;;
esac
;;
"ath10k/pre-cal-ahb-a800000.wifi.bin")
case "$board" in
8dev,habanero-dvk |\
8dev,jalapeno |\
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x5000 0x2f20
;;
aruba,ap-303 |\
aruba,ap-303h |\
aruba,ap-365)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) +1)
;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x2c)
;;
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
edgecore,ecw5211 |\
edgecore,oap100 |\
engenius,eap1300 |\
engenius,eap2200 |\
luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
caldata_extract "0:ART" 0x5000 0x2f20
;;
dlink,dap-2610)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
;;
engenius,emd1)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
;;
engenius,emr3500)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) +1)
;;
engenius,ens620ext)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
;;
meraki,mr33)
caldata_extract_ubi "ART" 0x5000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +3)
;;
netgear,ex6100v2 |\
netgear,ex6150v2)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc)
;;
zyxel,nbg6617 |\
zyxel,wre6606)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
;;
esac
;;
*)
exit 1
;;
esac