ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-23 07:22:33 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
a7c0c9bb7e
openwrt/target/linux/ramips/image/mt7621.mk
Sander Vanheule a7c0c9bb7e ramips: mt7621: add TP-Link EAP235-Wall support 
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.

When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.

The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.

Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
  * Back side: ETH0, PoE PD port
  * Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)

Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).

Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
    eth     a4:2b:b0:...:88
    ra0     a4:2b:b0:...:88
    rai0    a4:2b:b0:...:89

Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface

Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
  pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
  bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
    # tftpboot 84000000 openwrt-initramfs.bin
    # bootm

Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
  $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
      -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin

This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.

Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
  This was an issue with the ddc75ff704 version of mt76, but appears to
  have improved/disappeared with bc3963764d.
  Error notice example:
  [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout

Hardware was kindly provided for porting by Stijn Segers.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 1e75909a35)
2021-02-19 20:09:28 +01:00

1508 lines
42 KiB
Makefile
Raw Blame History

#
# MT7621 Profiles
#
include ./common-tp-link.mk
DEFAULT_SOC := mt7621
KERNEL_DTB += -d21
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME
define Build/elecom-wrc-gs-factory
$(eval product=$(word 1,$(1)))
$(eval version=$(word 2,$(1)))
$(eval hash_opt=$(word 3,$(1)))
$(STAGING_DIR_HOST)/bin/mkhash md5 $(hash_opt) $@ >> $@
( \
echo -n "ELECOM $(product) v$(version)" | \
dd bs=32 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/iodata-factory
$(eval fw_size=$(word 1,$(1)))
$(eval fw_type=$(word 2,$(1)))
$(eval product=$(word 3,$(1)))
$(eval factory_bin=$(word 4,$(1)))
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(fw_size)" ]; then \
$(CP) $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) $(factory_bin); \
$(STAGING_DIR_HOST)/bin/mksenaofw \
-r 0x30a -p $(product) -t $(fw_type) \
-e $(factory_bin) -o $(factory_bin).new; \
mv $(factory_bin).new $(factory_bin); \
$(CP) $(factory_bin) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/iodata-mstc-header
( \
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
)
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
( \
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
)
endef
define Build/ubnt-erx-factory-image
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
echo '21001:7' > $(1).compat; \
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
\
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
mkhash md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
\
echo "dummy" > $(1).rootfs; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
\
mkhash md5 $(1).rootfs > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
\
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
\
$(CP) $(1) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Device/dsa-migration
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
endef
define Device/adslr_g7
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ADSLR
DEVICE_MODEL := G7
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += adslr_g7
define Device/afoundry_ew1200
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := AFOUNDRY
DEVICE_MODEL := EW1200
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += ew1200
endef
TARGET_DEVICES += afoundry_ew1200
define Device/alfa-network_quad-e4g
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := Quad-E4G
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 uboot-envtools \
-wpad-basic-wolfssl
endef
TARGET_DEVICES += alfa-network_quad-e4g
define Device/asiarf_ap7621-001
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := AsiaRF
DEVICE_MODEL := AP7621-001
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += asiarf_ap7621-001
define Device/asiarf_ap7621-nv1
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := AsiaRF
DEVICE_MODEL := AP7621-NV1
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += asiarf_ap7621-nv1
define Device/asus_rt-ac57u
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC57U
IMAGE_SIZE := 16064k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac57u
define Device/asus_rt-ac65p
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC65P
IMAGE_SIZE := 51200k
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
endef
TARGET_DEVICES += asus_rt-ac65p
define Device/asus_rt-ac85p
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC85P
IMAGE_SIZE := 51200k
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
endef
TARGET_DEVICES += asus_rt-ac85p
define Device/asus_rt-n56u-b1
$(Device/dsa-migration)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-N56U
DEVICE_VARIANT := B1
IMAGE_SIZE := 16064k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-n56u-b1
define Device/buffalo_wsr-1166dhp
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
IMAGE_SIZE := 15936k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-1166DHP
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
SUPPORTED_DEVICES += wsr-1166
endef
TARGET_DEVICES += buffalo_wsr-1166dhp
define Device/buffalo_wsr-2533dhpl
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7936k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-2533DHPL
DEVICE_ALT0_VENDOR := Buffalo
DEVICE_ALT0_MODEL := WSR-2533DHP
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += buffalo_wsr-2533dhpl
define Device/buffalo_wsr-600dhp
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WSR-600DHP
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci
SUPPORTED_DEVICES += wsr-600
endef
TARGET_DEVICES += buffalo_wsr-600dhp
define Device/cudy_wr1300
$(Device/dsa-migration)
IMAGE_SIZE := 15872k
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR1300
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += cudy_wr1300
define Device/dlink_dir-8xx-a1
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
pad-rootfs | append-metadata | check-size
IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
check-size
endef
define Device/dlink_dir-8xx-r1
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
KERNEL_INITRAMFS := $$(KERNEL)
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs |\
pad-rootfs | append-metadata | check-size
endef
define Device/dlink_dir-xx60-a1
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE_SIZE := 40960k
UBINIZE_OPTS := -E 5
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
KERNEL := $$(KERNEL) | uimage-padhdr 96
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
endef
define Device/dlink_dir-1960-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-1960
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-1960-a1
define Device/dlink_dir-2640-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-2640
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-2640-a1
define Device/dlink_dir-2660-a1
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-2660
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-2660-a1
define Device/dlink_dir-860l-b1
$(Device/dsa-migration)
$(Device/seama)
BLOCKSIZE := 64k
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | relocate-kernel | \
lzma -a0 | uImage lzma
IMAGE_SIZE := 16064k
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-860L
DEVICE_VARIANT := B1
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += dir-860l-b1
endef
TARGET_DEVICES += dlink_dir-860l-b1
define Device/dlink_dir-867-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-867
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-867-a1
define Device/dlink_dir-878-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-878
DEVICE_VARIANT := A1
endef
TARGET_DEVICES += dlink_dir-878-a1
define Device/dlink_dir-882-a1
$(Device/dlink_dir-8xx-a1)
DEVICE_MODEL := DIR-882
DEVICE_VARIANT := A1
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += dlink_dir-882-a1
define Device/dlink_dir-882-r1
$(Device/dlink_dir-8xx-r1)
DEVICE_MODEL := DIR-882
DEVICE_VARIANT := R1
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
ab0dff19af8842cdb70a86b4b68d23f7
endef
TARGET_DEVICES += dlink_dir-882-r1
define Device/d-team_newifi-d2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Newifi
DEVICE_MODEL := D2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += d-team_newifi-d2
define Device/d-team_pbr-m1
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := PandoraBox
DEVICE_MODEL := PBR-M1
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += pbr-m1
endef
TARGET_DEVICES += d-team_pbr-m1
define Device/edimax_ra21s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := RA21S
DEVICE_ALT0_VENDOR := Edimax
DEVICE_ALT0_MODEL := Gemini RA21S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 02020040 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_ra21s
define Device/edimax_re23s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15680k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := RE23S
DEVICE_ALT0_VENDOR := Edimax
DEVICE_ALT0_MODEL := Gemini RE23S
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
append-metadata | check-size
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-rootfs | \
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_re23s
define Device/edimax_rg21s
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Edimax
DEVICE_MODEL := Gemini AC2600 RG21S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 02020038 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += edimax_rg21s
define Device/elecom_wrc-1167ghbk2-s
$(Device/dsa-migration)
IMAGE_SIZE := 15488k
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-1167GHBK2-S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
define Device/elecom_wrc-gs
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := ELECOM
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
define Device/elecom_wrc-1167gs2-b
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1167GS2-B
ELECOM_HWNAME := WRC-1167GS2
endef
TARGET_DEVICES += elecom_wrc-1167gs2-b
define Device/elecom_wrc-1167gst2
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 24576k
DEVICE_MODEL := WRC-1167GST2
ELECOM_HWNAME := WRC-1167GST2
endef
TARGET_DEVICES += elecom_wrc-1167gst2
define Device/elecom_wrc-1750gs
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1750GS
ELECOM_HWNAME := WRC-1750GS
endef
TARGET_DEVICES += elecom_wrc-1750gs
define Device/elecom_wrc-1750gsv
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1750GSV
ELECOM_HWNAME := WRC-1750GSV
endef
TARGET_DEVICES += elecom_wrc-1750gsv
define Device/elecom_wrc-1900gst
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-1900GST
ELECOM_HWNAME := WRC-1900GST
endef
TARGET_DEVICES += elecom_wrc-1900gst
define Device/elecom_wrc-2533ghbk-i
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-2533GHBK-I
IMAGE_SIZE := 9856k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 0107002d 8844A2D168B45A2D | \
elecom-product-header WRC-2533GHBK-I
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += elecom_wrc-2533ghbk-i
define Device/elecom_wrc-2533gst
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 11264k
DEVICE_MODEL := WRC-2533GST
ELECOM_HWNAME := WRC-2533GST
endef
TARGET_DEVICES += elecom_wrc-2533gst
define Device/elecom_wrc-2533gst2
$(Device/elecom_wrc-gs)
IMAGE_SIZE := 24576k
DEVICE_MODEL := WRC-2533GST2
ELECOM_HWNAME := WRC-2533GST2
endef
TARGET_DEVICES += elecom_wrc-2533gst2
define Device/firefly_firewrt
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Firefly
DEVICE_MODEL := FireWRT
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += firewrt
endef
TARGET_DEVICES += firefly_firewrt
define Device/gehua_ghl-r-001
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := GeHua
DEVICE_MODEL := GHL-R-001
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += gehua_ghl-r-001
define Device/glinet_gl-mt1300
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT1300
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += glinet_gl-mt1300
define Device/gnubee_gb-pc1
$(Device/dsa-migration)
DEVICE_VENDOR := GnuBee
DEVICE_MODEL := Personal Cloud One
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
IMAGE_SIZE := 32448k
endef
TARGET_DEVICES += gnubee_gb-pc1
define Device/gnubee_gb-pc2
$(Device/dsa-migration)
DEVICE_VENDOR := GnuBee
DEVICE_MODEL := Personal Cloud Two
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
IMAGE_SIZE := 32448k
endef
TARGET_DEVICES += gnubee_gb-pc2
define Device/hiwifi_hc5962
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32768k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_VENDOR := HiWiFi
DEVICE_MODEL := HC5962
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
endef
TARGET_DEVICES += hiwifi_hc5962
define Device/iodata_wn-ax1167gr
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15552k
KERNEL_INITRAMFS := $$(KERNEL) | \
iodata-factory 7864320 4 0x1055 $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AX1167GR
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += iodata_wn-ax1167gr
define Device/iodata_nand
$(Device/dsa-migration)
DEVICE_VENDOR := I-O DATA
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5
KERNEL_SIZE := 4096k
IMAGE_SIZE := 51200k
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
# The OEM webinterface expects an kernel with initramfs which has the uImage
# header field ih_name.
# We don't want to set the header name field for the kernel include in the
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
# webinterface. It will soft-brick the board.
define Device/iodata_wn-ax1167gr2
$(Device/iodata_nand)
DEVICE_MODEL := WN-AX1167GR2
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-ax1167gr2
define Device/iodata_wn-ax2033gr
$(Device/iodata_nand)
DEVICE_MODEL := WN-AX2033GR
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-ax2033gr
define Device/iodata_wn-dx1167r
$(Device/iodata_nand)
DEVICE_MODEL := WN-DX1167R
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wn-dx1167r
define Device/iodata_wn-dx1200gr
$(Device/iodata_nand)
DEVICE_MODEL := WN-DX1200GR
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
endef
TARGET_DEVICES += iodata_wn-dx1200gr
define Device/iodata_wn-gx300gr
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7616k
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-GX300GR
DEVICE_PACKAGES := kmod-mt7603
endef
TARGET_DEVICES += iodata_wn-gx300gr
define Device/iodata_wnpr2600g
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WNPR2600G
IMAGE_SIZE := 13952k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
elx-header 0104003a 8844A2D168B45A2D
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += iodata_wnpr2600g
define Device/iptime_a6ns-m
$(Device/dsa-migration)
IMAGE_SIZE := 16128k
UIMAGE_NAME := a6nm
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := A6ns-M
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += iptime_a6ns-m
define Device/iptime_a8004t
$(Device/dsa-migration)
IMAGE_SIZE := 16128k
UIMAGE_NAME := a8004t
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := A8004T
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += iptime_a8004t
define Device/jcg_jhr-ac876m
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
JCG_MAXSIZE := 16064k
DEVICE_VENDOR := JCG
DEVICE_MODEL := JHR-AC876M
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += jcg_jhr-ac876m
define Device/jcg_y2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
JCG_MAXSIZE := 16064k
DEVICE_VENDOR := JCG
DEVICE_MODEL := Y2
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
endef
TARGET_DEVICES += jcg_y2
define Device/lenovo_newifi-d1
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Newifi
DEVICE_MODEL := D1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += newifi-d1
endef
TARGET_DEVICES += lenovo_newifi-d1
define Device/linksys_ea7xxx
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE_SIZE := 36864k
DEVICE_VENDOR := Linksys
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware \
uboot-envtools
UBINIZE_OPTS := -E 5
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata | check-size
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
endef
define Device/linksys_ea7300-v1
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7300
DEVICE_VARIANT := v1
LINKSYS_HWNAME := EA7300
endef
TARGET_DEVICES += linksys_ea7300-v1
define Device/linksys_ea7300-v2
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7300
DEVICE_VARIANT := v2
LINKSYS_HWNAME := EA7300v2
DEVICE_PACKAGES += kmod-mt7603
endef
TARGET_DEVICES += linksys_ea7300-v2
define Device/linksys_ea7500-v2
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7500
DEVICE_VARIANT := v2
LINKSYS_HWNAME := EA7500v2
endef
TARGET_DEVICES += linksys_ea7500-v2
define Device/linksys_re6500
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Linksys
DEVICE_MODEL := RE6500
DEVICE_PACKAGES := kmod-mt76x2
SUPPORTED_DEVICES += re6500
endef
TARGET_DEVICES += linksys_re6500
define Device/mediatek_ap-mt7621a-v60
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Mediatek
DEVICE_MODEL := AP-MT7621A-V60 EVB
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 -wpad-basic-wolfssl
endef
TARGET_DEVICES += mediatek_ap-mt7621a-v60
define Device/mediatek_mt7621-eval-board
$(Device/dsa-migration)
BLOCKSIZE := 64k
IMAGE_SIZE := 15104k
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7621 EVB
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mt7621
endef
TARGET_DEVICES += mediatek_mt7621-eval-board
define Device/MikroTik
$(Device/dsa-migration)
DEVICE_VENDOR := MikroTik
BLOCKSIZE := 64k
IMAGE_SIZE := 16128k
DEVICE_PACKAGES := kmod-usb3
KERNEL_NAME := vmlinuz
KERNEL := kernel-bin | append-dtb-elf
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata | \
check-size
endef
define Device/mikrotik_routerboard-750gr3
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD 750Gr3
DEVICE_PACKAGES += -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rb750gr3
endef
TARGET_DEVICES += mikrotik_routerboard-750gr3
define Device/mikrotik_routerboard-760igs
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD 760iGS
DEVICE_PACKAGES += kmod-sfp -wpad-basic-wolfssl
endef
TARGET_DEVICES += mikrotik_routerboard-760igs
define Device/mikrotik_routerboard-m11g
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD M11G
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rbm11g
endef
TARGET_DEVICES += mikrotik_routerboard-m11g
define Device/mikrotik_routerboard-m33g
$(Device/MikroTik)
DEVICE_MODEL := RouterBOARD M33G
DEVICE_PACKAGES := -wpad-basic-wolfssl
SUPPORTED_DEVICES += mikrotik,rbm33g
endef
TARGET_DEVICES += mikrotik_routerboard-m33g
define Device/mqmaker_witi
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := MQmaker
DEVICE_MODEL := WiTi
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
endef
TARGET_DEVICES += mqmaker_witi
define Device/mtc_wr1201
$(Device/dsa-migration)
IMAGE_SIZE := 16000k
DEVICE_VENDOR := MTC
DEVICE_MODEL := Wireless Router WR1201
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mtc_wr1201
define Device/netgear_ex6150
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := EX6150
DEVICE_PACKAGES := kmod-mt76x2
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
IMAGE_SIZE := 14848k
IMAGES += factory.chk
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
endef
TARGET_DEVICES += netgear_ex6150
define Device/netgear_sercomm_nand
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGES += factory.img kernel.bin rootfs.bin
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-ubi | check-size
DEVICE_VENDOR := NETGEAR
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport
endef
define Device/netgear_r6220
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6220
SERCOMM_HWNAME := R6220
SERCOMM_HWID := AYA
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0086
IMAGE_SIZE := 28672k
DEVICE_PACKAGES += kmod-mt76x2
SUPPORTED_DEVICES += r6220
endef
TARGET_DEVICES += netgear_r6220
define Device/netgear_r6260
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6260
SERCOMM_HWNAME := R6260
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6260
define Device/netgear_r6350
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6350
SERCOMM_HWNAME := R6350
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6350
define Device/netgear_r6700-v2
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6700
DEVICE_VARIANT := v2
DEVICE_ALT0_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := Nighthawk AC2400
DEVICE_ALT0_VARIANT := v1
DEVICE_ALT1_VENDOR := NETGEAR
DEVICE_ALT1_MODEL := R7200
DEVICE_ALT1_VARIANT := v1
SERCOMM_HWNAME := R6950
SERCOMM_HWID := BZV
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x1032
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6700-v2
define Device/netgear_r6800
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6800
SERCOMM_HWNAME := R6950
SERCOMM_HWID := BZV
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0062
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6800
define Device/netgear_r6850
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6850
SERCOMM_HWNAME := R6850
SERCOMM_HWID := CHJ
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0052
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_r6850
define Device/netgear_wac104
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := WAC104
SERCOMM_HWNAME := WAC104
SERCOMM_HWID := CAY
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0006
IMAGE_SIZE := 28672k
DEVICE_PACKAGES += kmod-mt76x2
endef
TARGET_DEVICES += netgear_wac104
define Device/netgear_wac124
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := WAC124
SERCOMM_HWNAME := WAC124
SERCOMM_HWID := CTL
SERCOMM_HWVER := A003
SERCOMM_SWVER := 0x0402
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += netgear_wac124
define Device/netgear_wndr3700-v5
$(Device/dsa-migration)
$(Device/netgear_sercomm_nor)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 15232k
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v5
SERCOMM_HWNAME := WNDR3700v5
SERCOMM_HWID := AYB
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x1054
SERCOMM_PAD := 320k
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += wndr3700v5
endef
TARGET_DEVICES += netgear_wndr3700-v5
define Device/netis_wf2881
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
KERNEL_SIZE := 4096k
IMAGE_SIZE := 129280k
UBINIZE_OPTS := -E 5
UIMAGE_NAME := WF2881_0.0.00
KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2881 | uImage lzma
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_VENDOR := NETIS
DEVICE_MODEL := WF2881
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += netis_wf2881
define Device/phicomm_k2p
$(Device/dsa-migration)
IMAGE_SIZE := 15744k
DEVICE_VENDOR := Phicomm
DEVICE_MODEL := K2P
DEVICE_ALT0_VENDOR := Phicomm
DEVICE_ALT0_MODEL := KE 2P
SUPPORTED_DEVICES += k2p
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += phicomm_k2p
define Device/planex_vr500
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 65216k
DEVICE_VENDOR := Planex
DEVICE_MODEL := VR500
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += vr500
endef
TARGET_DEVICES += planex_vr500
define Device/samknows_whitebox-v8
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := SamKnows
DEVICE_MODEL := Whitebox 8
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
SUPPORTED_DEVICES += sk-wb8
endef
TARGET_DEVICES += samknows_whitebox-v8
define Device/storylink_sap-g3200u3
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := STORYLiNK
DEVICE_MODEL := SAP-G3200U3
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += sap-g3200u3
endef
TARGET_DEVICES += storylink_sap-g3200u3
define Device/telco-electronics_x1
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Telco Electronics
DEVICE_MODEL := X1
DEVICE_PACKAGES := kmod-usb3 kmod-mt76
endef
TARGET_DEVICES += telco-electronics_x1
define Device/thunder_timecloud
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Thunder
DEVICE_MODEL := Timecloud
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += timecloud
endef
TARGET_DEVICES += thunder_timecloud
define Device/totolink_a7000r
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := C8340R1C-9999
DEVICE_VENDOR := TOTOLINK
DEVICE_MODEL := A7000R
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += totolink_a7000r
define Device/totolink_x5000r
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := C8343R-9999
DEVICE_VENDOR := TOTOLINK
DEVICE_MODEL := X5000R
DEVICE_PACKAGES := kmod-mt7915e
endef
TARGET_DEVICES += totolink_x5000r
define Device/tplink_eap235-wall-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := EAP235-Wall
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
TPLINK_BOARD_ID := EAP235-WALL-V1
IMAGE_SIZE := 13440k
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
pad-extra 128
endef
TARGET_DEVICES += tplink_eap235-wall-v1
define Device/tplink_re350-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE350
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
TPLINK_BOARD_ID := RE350-V1
IMAGE_SIZE := 6016k
SUPPORTED_DEVICES += re350-v1
endef
TARGET_DEVICES += tplink_re350-v1
define Device/tplink_re500-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE500
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
TPLINK_BOARD_ID := RE500-V1
IMAGE_SIZE := 14208k
endef
TARGET_DEVICES += tplink_re500-v1
define Device/tplink_re650-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
DEVICE_MODEL := RE650
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
TPLINK_BOARD_ID := RE650-V1
IMAGE_SIZE := 14208k
endef
TARGET_DEVICES += tplink_re650-v1
define Device/ubnt_edgerouter_common
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := Ubiquiti
IMAGE_SIZE := 256768k
FILESYSTEMS := squashfs
KERNEL_SIZE := 3145728
KERNEL_INITRAMFS := $$(KERNEL) | \
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES += -wpad-basic-wolfssl
endef
define Device/ubnt_edgerouter-x
$(Device/ubnt_edgerouter_common)
DEVICE_MODEL := EdgeRouter X
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
endef
TARGET_DEVICES += ubnt_edgerouter-x
define Device/ubnt_edgerouter-x-sfp
$(Device/ubnt_edgerouter_common)
DEVICE_MODEL := EdgeRouter X SFP
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
endef
TARGET_DEVICES += ubnt_edgerouter-x-sfp
define Device/ubnt_unifi-6-lite
$(Device/dsa-migration)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi 6 Lite
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915e
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
IMAGE_SIZE := 15424k
endef
TARGET_DEVICES += ubnt_unifi-6-lite
define Device/ubnt_unifi-nanohd
$(Device/dsa-migration)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi nanoHD
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
IMAGE_SIZE := 15552k
endef
TARGET_DEVICES += ubnt_unifi-nanohd
define Device/unielec_u7621-01-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-01
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
endef
TARGET_DEVICES += unielec_u7621-01-16m
define Device/unielec_u7621-06-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-06
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
endef
TARGET_DEVICES += unielec_u7621-06-16m
define Device/unielec_u7621-06-64m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 65216k
DEVICE_VENDOR := UniElec
DEVICE_MODEL := U7621-06
DEVICE_VARIANT := 64M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
endef
TARGET_DEVICES += unielec_u7621-06-64m
define Device/wavlink_wl-wn531a6
$(Device/dsa-migration)
DEVICE_VENDOR := Wavlink
DEVICE_MODEL := WL-WN531A6
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware kmod-usb3
IMAGE_SIZE := 15040k
endef
TARGET_DEVICES += wavlink_wl-wn531a6
define Device/wevo_11acnas
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
DEVICE_VENDOR := WeVO
DEVICE_MODEL := 11AC NAS Router
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += 11acnas
endef
TARGET_DEVICES += wevo_11acnas
define Device/wevo_w2914ns-v2
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
UIMAGE_NAME := W2914NS-V2(0.0.0)
DEVICE_VENDOR := WeVO
DEVICE_MODEL := W2914NS
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += w2914nsv2
endef
TARGET_DEVICES += wevo_w2914ns-v2
define Device/winstars_ws-wn583a6
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 7872k
DEVICE_VENDOR := Winstars
DEVICE_MODEL := WS-WN583A6
DEVICE_ALT0_VENDOR := Gemeita
DEVICE_ALT0_MODEL := AC2100
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += winstars_ws-wn583a6
define Device/xiaomi_nand_separate
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
DEVICE_VENDOR := Xiaomi
DEVICE_PACKAGES := uboot-envtools
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGES += kernel1.bin rootfs0.bin
IMAGE/kernel1.bin := append-kernel
IMAGE/rootfs0.bin := append-ubi | check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/xiaomi_mi-router-3g
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router 3G
IMAGE_SIZE := 124416k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
endef
TARGET_DEVICES += xiaomi_mi-router-3g
define Device/xiaomi_mi-router-3g-v2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 14848k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 3G
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
SUPPORTED_DEVICES += xiaomi,mir3g-v2
endef
TARGET_DEVICES += xiaomi_mi-router-3g-v2
define Device/xiaomi_mi-router-3-pro
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE:= 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 255488k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 3 Pro
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
SUPPORTED_DEVICES += xiaomi,mir3p
endef
TARGET_DEVICES += xiaomi_mi-router-3-pro
define Device/xiaomi_mi-router-4
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router 4
IMAGE_SIZE := 124416k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += xiaomi_mi-router-4
define Device/xiaomi_mi-router-4a-gigabit
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 14848k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4A
DEVICE_VARIANT := Gigabit Edition
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
define Device/xiaomi_mi-router-ac2100
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router AC2100
IMAGE_SIZE := 120320k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += xiaomi_mi-router-ac2100
define Device/xiaomi_redmi-router-ac2100
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Redmi Router AC2100
IMAGE_SIZE := 120320k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
endef
TARGET_DEVICES += xiaomi_redmi-router-ac2100
define Device/xiaoyu_xy-c5
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := XiaoYu
DEVICE_MODEL := XY-C5
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += xiaoyu_xy-c5
define Device/xzwifi_creativebox-v1
$(Device/dsa-migration)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := CreativeBox
DEVICE_MODEL := v1
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
kmod-usb3 -wpad-basic-wolfssl
endef
TARGET_DEVICES += xzwifi_creativebox-v1
define Device/youhua_wr1200js
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := YouHua
DEVICE_MODEL := WR1200JS
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += youhua_wr1200js
define Device/youku_yk-l2
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Youku
DEVICE_MODEL := YK-L2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += youku_yk-l2
define Device/zbtlink_zbt-we1326
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WE1326
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620
SUPPORTED_DEVICES += zbt-we1326
endef
TARGET_DEVICES += zbtlink_zbt-we1326
define Device/zbtlink_zbt-we3526
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WE3526
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zbtlink_zbt-we3526
define Device/zbtlink_zbt-wg2626
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG2626
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += zbt-wg2626
endef
TARGET_DEVICES += zbtlink_zbt-wg2626
define Device/zbtlink_zbt-wg3526-16m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG3526
DEVICE_VARIANT := 16M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
endef
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
define Device/zbtlink_zbt-wg3526-32m
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 32448k
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-WG3526
DEVICE_VARIANT := 32M
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
endef
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
define Device/zio_freezio
$(Device/dsa-migration)
IMAGE_SIZE := 16064k
DEVICE_VENDOR := ZIO
DEVICE_MODEL := FREEZIO
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zio_freezio
define Device/zyxel_wap6805
$(Device/dsa-migration)
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32448k
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WAP6805
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii
KERNEL := $(KERNEL_DTB) | uImage lzma | uimage-padhdr 160
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_wap6805
Reference in New Issue View Git Blame Copy Permalink