mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
131 lines
2.0 KiB
Plaintext
131 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "partition-table";
|
|
reg = <0x020000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@30000 {
|
|
label = "info";
|
|
reg = <0x030000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
compatible = "openwrt,elf";
|
|
label = "firmware";
|
|
reg = <0x040000 0xd80000>;
|
|
};
|
|
|
|
partition@dc0000 {
|
|
label = "config";
|
|
reg = <0xdc0000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
/* df0000-f30000 undefined in vendor firmware */
|
|
|
|
partition@f30000 {
|
|
label = "log";
|
|
reg = <0xf30000 0x0c0000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
mdio_pins: mdio_pins {
|
|
/* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
|
|
pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
|
|
phy-mask = <0x10>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "sgmii";
|
|
|
|
mtd-mac-address = <&info 0x8>;
|
|
|
|
qca956x-serdes-fixup;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|