mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
135 lines
2.0 KiB
Plaintext
135 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
keys: keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wifi {
|
|
label = "WiFi on/off button";
|
|
linux,code = <KEY_RFKILL>;
|
|
linux,input-type = <EV_SW>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
gpio_usb_power: usb_power {
|
|
gpio-hog;
|
|
gpios = <16 0>;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy17: ethernet-phy@11 {
|
|
reg = <0x11>;
|
|
phy-mode = "rgmii-id";
|
|
};
|
|
|
|
switch0@1f {
|
|
compatible = "qca,ar8327";
|
|
reg = <0x1f>;
|
|
qca,ar8327-initvals = <
|
|
0x04 0x87600000 /* PORT0 PAD MODE CTRL */
|
|
0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
|
|
0x10 0x81000080 /* POWER_ON_STRAP */
|
|
0x50 0xffb7ffb7 /* LED_CTRL0 */
|
|
0x54 0xffb7ffb7 /* LED_CTRL1 */
|
|
0x58 0xffb7ffb7 /* LED_CTRL2 */
|
|
0x5c 0x03ffff00 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x94 0x0000007e /* PORT6 STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&mdio1 {
|
|
status = "okay";
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
};
|
|
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0xa6000000 0x00000101 0x00001616>;
|
|
phy-handle = <&phy17>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001616>;
|
|
phy-handle = <&phy1>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
|
|
hub_port0: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
|
|
};
|
|
|
|
&usb1 {
|
|
status = "okay";
|
|
|
|
hub_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|