mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
137 lines
2.0 KiB
Plaintext
137 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9330.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "PQI Air-Pen";
|
|
compatible = "pqi,air-pen", "qca,ar9330";
|
|
|
|
aliases {
|
|
led-boot = &led_wlan;
|
|
led-failsafe = &led_wlan;
|
|
led-upgrade = &led_wlan;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_wlan: wlan {
|
|
label = "blue:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wps {
|
|
label = "blue:wps";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
art: partition@50000 {
|
|
label = "art";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "NVRAM";
|
|
reg = <0x060000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x070000 0x780000>;
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "CONF";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x1002>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x2>;
|
|
};
|