mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 02:29:01 +00:00
77e850fe76
Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and have their port set to LAN by default. Setting up a WAN MAC address for them doesn't make any sense, as no wan interface will be created in uci config. Despite, these devices also set lan_mac in 02_network, although mtd-mac-address sets a different address for the ethernet interface in DTS. Clean this up by moving the lan_mac value into DTS and dropping the entries in 02_network completely. That way, the effective address on the LAN interface should stay the same, but we get rid of the extra (re)assignments. As I don't have access to the devices, this does not tell anything about whether 0x2e is actually a good choice, it just preserves the existing assignment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
165 lines
2.2 KiB
Plaintext
165 lines
2.2 KiB
Plaintext
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "onion,omega2", "mediatek,mt7628an-soc";
|
|
|
|
aliases {
|
|
led-boot = &system_led;
|
|
led-failsafe = &system_led;
|
|
led-running = &system_led;
|
|
led-upgrade = &system_led;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
system_led: system {
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "gpio";
|
|
function = "gpio";
|
|
};
|
|
|
|
perst {
|
|
groups = "perst";
|
|
function = "gpio";
|
|
};
|
|
|
|
refclk {
|
|
groups = "refclk";
|
|
function = "gpio";
|
|
};
|
|
|
|
i2s {
|
|
groups = "i2s";
|
|
function = "gpio";
|
|
};
|
|
|
|
spis {
|
|
groups = "spis";
|
|
function = "gpio";
|
|
};
|
|
|
|
wled_kn {
|
|
groups = "wled_kn";
|
|
function = "gpio";
|
|
};
|
|
|
|
wled_an {
|
|
groups = "wled_an";
|
|
function = "gpio";
|
|
};
|
|
|
|
wdt {
|
|
groups = "wdt";
|
|
function = "gpio";
|
|
};
|
|
|
|
pwm0 {
|
|
groups = "pwm0";
|
|
function = "gpio";
|
|
};
|
|
|
|
pwm1 {
|
|
groups = "pwm1";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi_pins>, <&spi_cs1_pins>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
firmware: partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
};
|
|
};
|
|
};
|
|
|
|
spidev@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "linux,spidev";
|
|
reg = <1>;
|
|
spi-max-frequency = <40000000>;
|
|
};
|
|
};
|
|
|
|
&i2c {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x2e>;
|
|
};
|
|
|
|
&sdhci {
|
|
status = "okay";
|
|
mediatek,cd-low;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
};
|