openwrt/target/linux/lantiq/dts/ARV7510PW22.dts
Martin Blumenstingl 6b94234a65 lantiq: remove "init" kernel command line parameter from bootargs
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-12-12 09:57:40 +01:00

192 lines
3.5 KiB
Plaintext

/dts-v1/;
#include "danube.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "ARV7510PW22 - Astoria Networks";
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-internet = &internet;
led-usb = &umts;
led-wifi = &wlan;
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x40000>;
read-only;
};
partition@40000 {
label = "uboot_env";
reg = <0x40000 0x20000>;
read-only;
};
partition@60000 {
label = "firmware";
reg = <0x60000 0xf80000>;
};
boardconfig: partition@fe0000 {
label = "board_config";
reg = <0xfe0000 0x20000>;
read-only;
};
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
exin {
lantiq,groups = "exin1";
lantiq,function = "exin";
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_in {
lantiq,groups = "req1", "req2";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
pins_out {
lantiq,pins = "io2", "io4", "io8", "io9", "io10", "io15", "io20";
lantiq,output = <1>;
};
pins_in {
lantiq,pins = "io11", "io12", "io28";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
};
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
};
etop@E180000 {
/* Switch reset 19 */
phy-mode = "mii";
mtd-mac-address = <&boardconfig 0x16>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
restart {
label = "restart";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
};
reset {
label = "reset";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
internet: internet {
label = "internet";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
wlan: wlan {
label = "wlan";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
umts: 3g {
label = "3g";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
message {
label = "message";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
};
};
&pci0 {
status = "okay";
lantiq,external-clock;
interrupt-map = <
0x7000 0 0 1 &icu0 30
0x7800 0 0 1 &icu0 135
0x7800 0 0 2 &icu0 135
0x7800 0 0 3 &icu0 135
>;
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
req-mask = <0x3>;
wifi@1814,3592 {
compatible = "pci1814,3592";
reg = <0x7000 0 0 0 0>;
ralink,mtd-eeprom = <&boardconfig 0x410>;
ralink,mtd-eeprom-swap;
};
};