openwrt/target/linux/lantiq/dts/ARV4518PWR01.dtsi
Martin Blumenstingl 6b94234a65 lantiq: remove "init" kernel command line parameter from bootargs
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-12-12 09:57:40 +01:00

195 lines
3.5 KiB
Plaintext

#include "danube.dtsi"
#include <dt-bindings/input/input.h>
/ {
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-dsl = &dsl;
led-internet = &online;
led-usb = &usb;
led-wifi = &wifi;
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
gpios = <&gpio 31 GPIO_ACTIVE_HIGH>;
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x2000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x10000>; /* 64 KB */
read-only;
};
partition@10000 {
label = "uboot_env";
reg = <0x10000 0x10000>; /* 64 KB */
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x20000 0x3d0000>;
};
boardconfig: partition@400000 {
label = "boardconfig";
reg = <0x3f0000 0x10000>;
read-only;
};
};
};
gpiomm: gpiomm@4000000 {
compatible = "lantiq,gpio-mm";
reg = <1 0x0 0x10 >;
#address-cells = <1>;
#size-cells = <1>;
#gpio-cells = <2>;
gpio-controller;
lantiq,shadow = <0x0>;
};
ath5k_eep {
compatible = "ath5k,eeprom";
ath,eep-flash = <&boardconfig 0x400>;
ath,mac-offset = <0x16>;
ath,mac-increment = <1>;
ath,eep-swap;
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ebu {
lantiq,groups = "ebu cs1";
lantiq,function = "ebu";
};
pci_in {
lantiq,groups = "req1", "req2";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1", "gnt2";
lantiq,function = "pci";
lantiq,pull = <0>;
lantiq,output = <1>;
};
};
};
etop@E180000 {
phy-mode = "mii";
mtd-mac-address = <&boardconfig 0x16>;
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
};
pci@E105400 {
status = "okay";
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
req-mask = <0xf>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "power";
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
default-state = "keep";
};
dsl: dsl {
label = "dsl";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
online: online {
label = "online";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
};
wifi: wifi {
label = "wifi";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
wps {
label = "wps";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
};
dsl2 {
label = "dsl2";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
usb: usb {
label = "usb";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
};
voice {
label = "voice";
gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>;
};
fxs1 {
label = "fxs1";
gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>;
};
fxs2 {
label = "fxs2";
gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>;
};
fxo {
label = "fxo";
gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>;
};
};
};