mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
2dde2416e1
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim <git@won-jung.kim> (added led dt-bindings) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
173 lines
2.8 KiB
Plaintext
173 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
compatible = "iptime,a3004t", "mediatek,mt7621-soc";
|
|
model = "ipTIME A3004T";
|
|
|
|
aliases {
|
|
led-boot = &led_cpu;
|
|
led-failsafe = &led_cpu;
|
|
led-running = &led_cpu;
|
|
led-upgrade = &led_cpu;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_cpu: led-0 {
|
|
label = "amber:cpu";
|
|
color = <LED_COLOR_ID_AMBER>;
|
|
function = LED_FUNCTION_CPU;
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led-1 {
|
|
color = <LED_COLOR_ID_AMBER>;
|
|
function = LED_FUNCTION_WLAN;
|
|
function-enumerator = <0>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0radio";
|
|
};
|
|
|
|
led-2 {
|
|
color = <LED_COLOR_ID_AMBER>;
|
|
function = LED_FUNCTION_WLAN;
|
|
function-enumerator = <1>;
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1radio";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "config";
|
|
reg = <0x80000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@a0000 {
|
|
label = "factory";
|
|
reg = <0xa0000 0x20000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_factory_4: macaddr@4 {
|
|
reg = <0x4 0x6>;
|
|
};
|
|
|
|
macaddr_factory_8004: macaddr@8004 {
|
|
reg = <0x8004 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "firmware";
|
|
reg = <0x140000 0x7e40000>;
|
|
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "kernel";
|
|
reg = <0x0 0x400000>;
|
|
};
|
|
|
|
partition@400000 {
|
|
label = "ubi";
|
|
reg = <0x400000 0x7a40000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <(3)>;
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
port@0 {
|
|
status = "okay";
|
|
label = "wan";
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <(1)>;
|
|
};
|
|
|
|
port@1 {
|
|
status = "okay";
|
|
label = "lan4";
|
|
};
|
|
|
|
port@2 {
|
|
status = "okay";
|
|
label = "lan3";
|
|
};
|
|
|
|
port@3 {
|
|
status = "okay";
|
|
label = "lan2";
|
|
};
|
|
|
|
port@4 {
|
|
status = "okay";
|
|
label = "lan1";
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "i2c", "jtag", "wdt";
|
|
function = "gpio";
|
|
};
|
|
};
|