mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
e4ce3109f2
The node pinctrl0 is already set up in the SOC DTSI files, but defined again as member of pinctrl in most of the device DTS(I) files. This patch removes this redundancy for the entire ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
182 lines
2.9 KiB
Plaintext
182 lines
2.9 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "buffalo,whr-1166d", "ralink,mt7620a-soc";
|
|
model = "Buffalo WHR-1166D";
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_green;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "whr-1166d:red:power";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi {
|
|
label = "whr-1166d:green:wifi";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_power_green: power2 {
|
|
label = "whr-1166d:green:power";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi2 {
|
|
label = "whr-1166d:orange:wifi";
|
|
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
internet {
|
|
label = "whr-1166d:green:internet";
|
|
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router {
|
|
label = "whr-1166d:orange:router";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router2 {
|
|
label = "whr-1166d:green:router";
|
|
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
aoss {
|
|
label = "aoss";
|
|
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
bridge {
|
|
label = "bridge";
|
|
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
ralink,group = "i2c", "uartf", "wled", "nd_sd";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
|
|
|
mtd-mac-address = <&factory 0x4>;
|
|
|
|
port@5 {
|
|
status = "okay";
|
|
phy-handle = <&phy5>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
phy-mode = "rgmii-rxid";
|
|
};
|
|
};
|
|
};
|
|
|
|
&gsw {
|
|
mediatek,port4 = "ephy";
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
};
|
|
};
|