openwrt/target/linux/bcm27xx/patches-6.6/950-0262-Input-edt-ft5x06-Poll-the-device-if-no-interrupt-is-.patch

From 5e768fe3e14ce0026a297dffd0d3c28ae2f73e72 Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
Date: Fri, 6 Nov 2020 18:45:10 +0000
Subject: [PATCH 0262/1085] Input: edt-ft5x06: Poll the device if no interrupt
 is configured.

Not all systems have the interrupt line wired up, so switch to
polling the touchscreen off a timer if no interrupt line is
configured.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

input: edt-ft5x06: Handle unreliable TOUCH_UP events

The ft5x06 is unreliable in sending touch up events, so some
touch IDs can become stuck in the detected state.

Ensure that IDs that are unreported by the controller are
released.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

input: edt-ft5x06: Only look at the number of points reported

Register 0x02 in the FT5x06 is TD_STATUS containing the number
of valid touch points being reported.

Iterate over that number of points rather than all that are
supported on the device.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

input: edt-ft5x06: Only read data for number of points reported

Rather than always reading the maximum number of points supported
by the chip (which may be as high as 10), read the number of
active points first, and read data for just those.
In most cases this will result in less data on the I2C bus,
with only the maximum touch points taking more due to a second
read that has to configure the start address.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

input: edt-ft5x06: Fix patch reading only the number of points reported

Fix bad conflict resolution from upstream updates. Need to read
from tsdata->tdata_offset bytes, not from tsdata->offset.
Also fix logging of i2c read errors to cover both transactions.

Fixes: 7216fcfe2e5f ("input: edt-ft5x06: Only read data for number of points reported")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
 drivers/input/touchscreen/edt-ft5x06.c | 93 ++++++++++++++++++++++----
 1 file changed, 80 insertions(+), 13 deletions(-)

--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -80,6 +80,8 @@
 #define M06_REG_CMD(factory) ((factory) ? 0xf3 : 0xfc)
 #define M06_REG_ADDR(factory, addr) ((factory) ? (addr) & 0x7f : (addr) & 0x3f)
 
+#define POLL_INTERVAL_MS		17	/* 17ms = 60fps */
+
 enum edt_pmode {
 	EDT_PMODE_NOT_SUPPORTED,
 	EDT_PMODE_HIBERNATE,
@@ -139,6 +141,7 @@ struct edt_ft5x06_ts_data {
 	u8 tdata_cmd;
 	int tdata_len;
 	int tdata_offset;
+	unsigned int known_ids;
 
 	char name[EDT_NAME_LEN];
 	char fw_version[EDT_NAME_LEN];
@@ -147,6 +150,9 @@ struct edt_ft5x06_ts_data {
 	enum edt_ver version;
 	unsigned int crc_errors;
 	unsigned int header_errors;
+
+	struct timer_list timer;
+	struct work_struct work_i2c_poll;
 };
 
 struct edt_i2c_chip_data {
@@ -303,17 +309,34 @@ static irqreturn_t edt_ft5x06_ts_isr(int
 	u8 rdbuf[63];
 	int i, type, x, y, id;
 	int error;
+	int num_points;
+	unsigned int active_ids = 0, known_ids = tsdata->known_ids;
+	long released_ids;
+	int b = 0;
 
 	memset(rdbuf, 0, sizeof(rdbuf));
 	error = regmap_bulk_read(tsdata->regmap, tsdata->tdata_cmd, rdbuf,
 				 tsdata->tdata_len);
+	if (tsdata->version == EDT_M06) {
+		num_points = tsdata->max_support_points;
+	} else {
+		/* Register 2 is TD_STATUS, containing the number of touch
+		 * points.
+		 */
+		num_points = min(rdbuf[2] & 0xf, tsdata->max_support_points);
+		if (!error && num_points)
+			error = regmap_bulk_read(tsdata->regmap,
+						 tsdata->tdata_offset,
+						 &rdbuf[tsdata->tdata_offset],
+						 tsdata->point_len * num_points);
+	}
 	if (error) {
 		dev_err_ratelimited(dev, "Unable to fetch data, error: %d\n",
 				    error);
 		goto out;
 	}
 
-	for (i = 0; i < tsdata->max_support_points; i++) {
+	for (i = 0; i < num_points; i++) {
 		u8 *buf = &rdbuf[i * tsdata->point_len + tsdata->tdata_offset];
 
 		type = buf[0] >> 6;
@@ -335,10 +358,25 @@ static irqreturn_t edt_ft5x06_ts_isr(int
 
 		input_mt_slot(tsdata->input, id);
 		if (input_mt_report_slot_state(tsdata->input, MT_TOOL_FINGER,
-					       type != TOUCH_EVENT_UP))
+					       type != TOUCH_EVENT_UP)) {
 			touchscreen_report_pos(tsdata->input, &tsdata->prop,
 					       x, y, true);
+			active_ids |= BIT(id);
+		} else {
+			known_ids &= ~BIT(id);
+		}
+	}
+
+	/* One issue with the device is the TOUCH_UP message is not always
+	 * returned. Instead track which ids we know about and report when they
+	 * are no longer updated
+	 */
+	released_ids = known_ids & ~active_ids;
+	for_each_set_bit_from(b, &released_ids, tsdata->max_support_points) {
+		input_mt_slot(tsdata->input, b);
+		input_mt_report_slot_inactive(tsdata->input);
 	}
+	tsdata->known_ids = active_ids;
 
 	input_mt_report_pointer_emulation(tsdata->input, true);
 	input_sync(tsdata->input);
@@ -347,6 +385,22 @@ out:
 	return IRQ_HANDLED;
 }
 
+static void edt_ft5x06_ts_irq_poll_timer(struct timer_list *t)
+{
+	struct edt_ft5x06_ts_data *tsdata = from_timer(tsdata, t, timer);
+
+	schedule_work(&tsdata->work_i2c_poll);
+	mod_timer(&tsdata->timer, jiffies + msecs_to_jiffies(POLL_INTERVAL_MS));
+}
+
+static void edt_ft5x06_ts_work_i2c_poll(struct work_struct *work)
+{
+	struct edt_ft5x06_ts_data *tsdata = container_of(work,
+			struct edt_ft5x06_ts_data, work_i2c_poll);
+
+	edt_ft5x06_ts_isr(0, tsdata);
+}
+
 struct edt_ft5x06_attribute {
 	struct device_attribute dattr;
 	size_t field_offset;
@@ -1053,20 +1107,23 @@ static void edt_ft5x06_ts_get_parameters
 static void edt_ft5x06_ts_set_tdata_parameters(struct edt_ft5x06_ts_data *tsdata)
 {
 	int crclen;
+	int points;
 
 	if (tsdata->version == EDT_M06) {
 		tsdata->tdata_cmd = 0xf9;
 		tsdata->tdata_offset = 5;
 		tsdata->point_len = 4;
 		crclen = 1;
+		points = tsdata->max_support_points;
 	} else {
 		tsdata->tdata_cmd = 0x0;
 		tsdata->tdata_offset = 3;
 		tsdata->point_len = 6;
 		crclen = 0;
+		points = 0;
 	}
 
-	tsdata->tdata_len = tsdata->point_len * tsdata->max_support_points +
+	tsdata->tdata_len = tsdata->point_len * points +
 		tsdata->tdata_offset + crclen;
 }
 
@@ -1335,17 +1392,27 @@ static int edt_ft5x06_ts_probe(struct i2
 		return error;
 	}
 
-	irq_flags = irq_get_trigger_type(client->irq);
-	if (irq_flags == IRQF_TRIGGER_NONE)
-		irq_flags = IRQF_TRIGGER_FALLING;
-	irq_flags |= IRQF_ONESHOT;
-
-	error = devm_request_threaded_irq(&client->dev, client->irq,
-					  NULL, edt_ft5x06_ts_isr, irq_flags,
-					  client->name, tsdata);
-	if (error) {
-		dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
-		return error;
+	if (client->irq) {
+		irq_flags = irq_get_trigger_type(client->irq);
+		if (irq_flags == IRQF_TRIGGER_NONE)
+			irq_flags = IRQF_TRIGGER_FALLING;
+		irq_flags |= IRQF_ONESHOT;
+
+		error = devm_request_threaded_irq(&client->dev, client->irq,
+						  NULL, edt_ft5x06_ts_isr,
+						  irq_flags, client->name,
+						  tsdata);
+		if (error) {
+			dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
+			return error;
+		}
+	} else {
+		INIT_WORK(&tsdata->work_i2c_poll,
+			  edt_ft5x06_ts_work_i2c_poll);
+		timer_setup(&tsdata->timer, edt_ft5x06_ts_irq_poll_timer, 0);
+		tsdata->timer.expires = jiffies +
+					msecs_to_jiffies(POLL_INTERVAL_MS);
+		add_timer(&tsdata->timer);
 	}
 
 	error = devm_device_add_group(&client->dev, &edt_ft5x06_attr_group);