mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
fce21ae4cc
Right now all brcm2708 patches are extracted from the non-mainline raspberrypi/linux git tree. Many of them are hacks and/or are unneeded in LEDE. Raspberry Pi is getting better and better mainline support so it would be nice to finally start maintaining patches in a cleaner way: 1) Backport patches accepted in upstream tree 2) Start using upstream drivers 3) Pick only these patches that are needed for more complete support Handling above tasks requires grouping patches - ideally using the same prefixes as generic ones. It means we should rename existing patches to use some high prefix. This will allow e.g. use 0xx for backported code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
81 lines
2.5 KiB
Diff
81 lines
2.5 KiB
Diff
From 6603973d0897c1a9b3b1a813c8ab1204efe98fe0 Mon Sep 17 00:00:00 2001
|
|
From: Phil Elwell <phil@raspberrypi.org>
|
|
Date: Wed, 24 Jun 2015 14:10:44 +0100
|
|
Subject: [PATCH] spi-bcm2835: Support pin groups other than 7-11
|
|
|
|
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
|
|
some unreliability of the native ones. In doing so it chooses the
|
|
same pins as the native chip-selects would use, but the existing
|
|
code always uses pins 7 and 8, wherever the SPI function is mapped.
|
|
|
|
Search the pinctrl group assigned to the driver for pins that
|
|
correspond to native chip-selects, and use those for GPIO chip-
|
|
selects.
|
|
|
|
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
|
|
---
|
|
drivers/spi/spi-bcm2835.c | 45 +++++++++++++++++++++++++++++++++++++--------
|
|
1 file changed, 37 insertions(+), 8 deletions(-)
|
|
|
|
--- a/drivers/spi/spi-bcm2835.c
|
|
+++ b/drivers/spi/spi-bcm2835.c
|
|
@@ -688,6 +688,8 @@ static int bcm2835_spi_setup(struct spi_
|
|
{
|
|
int err;
|
|
struct gpio_chip *chip;
|
|
+ struct device_node *pins;
|
|
+ u32 pingroup_index;
|
|
/*
|
|
* sanity checking the native-chipselects
|
|
*/
|
|
@@ -704,15 +706,42 @@ static int bcm2835_spi_setup(struct spi_
|
|
"setup: only two native chip-selects are supported\n");
|
|
return -EINVAL;
|
|
}
|
|
- /* now translate native cs to GPIO */
|
|
|
|
- /* get the gpio chip for the base */
|
|
- chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
|
|
- if (!chip)
|
|
- return 0;
|
|
+ /* now translate native cs to GPIO */
|
|
+ /* first look for chip select pins in the devices pin groups */
|
|
+ for (pingroup_index = 0;
|
|
+ (pins = of_parse_phandle(spi->master->dev.of_node,
|
|
+ "pinctrl-0",
|
|
+ pingroup_index)) != 0;
|
|
+ pingroup_index++) {
|
|
+ u32 pin;
|
|
+ u32 pin_index;
|
|
+ for (pin_index = 0;
|
|
+ of_property_read_u32_index(pins,
|
|
+ "brcm,pins",
|
|
+ pin_index,
|
|
+ &pin) == 0;
|
|
+ pin_index++) {
|
|
+ if (((spi->chip_select == 0) &&
|
|
+ ((pin == 8) || (pin == 36) || (pin == 46))) ||
|
|
+ ((spi->chip_select == 1) &&
|
|
+ ((pin == 7) || (pin == 35)))) {
|
|
+ spi->cs_gpio = pin;
|
|
+ break;
|
|
+ }
|
|
+ }
|
|
+ of_node_put(pins);
|
|
+ }
|
|
+ /* if that fails, assume GPIOs 7-11 are used */
|
|
+ if (!gpio_is_valid(spi->cs_gpio) ) {
|
|
+ /* get the gpio chip for the base */
|
|
+ chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
|
|
+ if (!chip)
|
|
+ return 0;
|
|
|
|
- /* and calculate the real CS */
|
|
- spi->cs_gpio = chip->base + 8 - spi->chip_select;
|
|
+ /* and calculate the real CS */
|
|
+ spi->cs_gpio = chip->base + 8 - spi->chip_select;
|
|
+ }
|
|
|
|
/* and set up the "mode" and level */
|
|
dev_info(&spi->dev, "setting up native-CS%i as GPIO %i\n",
|