openwrt/target/linux/ath79/dts/ar9344_enterasys_ws-ap3705i.dts
David Bauer ebddc5f984 ath79: add support for Enterasys WS-AP3705i
Hardware
--------
SoC:    Atheros AR9344
RAM:    128M DDR2
FLASH:  2x Macronix MX25L12845EM
        2x 16MiB SPI-NOR
WLAN2:  Atheros AR9344 2x2 2T2R
WLAN5:  Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)

Installation
------------

The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot 0x85000000; bootm'
   $ setenv bootcmd 'run boot_openwrt'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-22 21:54:30 +02:00

237 lines
3.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
compatible = "enterasys,ws-ap3705i", "qca,ar9344";
model = "Enterasys WS-AP3705i";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_red;
led-running = &led_power_green;
led-upgrade = &led_power_red;
label-mac-device = &eth0;
};
mtd-concat {
compatible = "mtd-concat";
devices = <&concat0 &concat1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x0 0x1dd0000>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&enable_gpio_11 &enable_gpio_16>;
led_power_green: power_green {
label = "ws-ap3705i:green:power";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
led_power_red: power_red {
label = "ws-ap3705i:red:power";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
lan_blue {
label = "ws-ap3705i:blue:lan";
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
lan_green {
label = "ws-ap3705i:green:lan";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
};
radio2 {
label = "ws-ap3705i:green:radio2";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
ath9k-leds {
compatible = "gpio-leds";
radio1 {
label = "ws-ap3705i:green:radio1";
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&pinmux {
enable_gpio_16: pinmux_enable_gpio_16 {
pinctrl-single,bits = <0x10 0x0 0x000000ff>;
};
enable_gpio_11: pinmux_enable_gpio_11 {
pinctrl-single,bits = <0x8 0x0 0xff000000>;
};
};
&gpio {
status = "okay";
};
&wmac {
status = "okay";
qca,no-eeprom;
};
&spi {
status = "okay";
cs-gpios = <0>, <0>;
num-cs = <2>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot-bak";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "u-boot-env0";
reg = <0x80000 0x10000>;
read-only;
};
partition@90000 {
label = "u-boot-env1";
reg = <0x90000 0x10000>;
read-only;
};
partition@a0000 {
label = "u-boot";
reg = <0xa0000 0x80000>;
read-only;
};
partition@120000 {
label = "calibrate";
reg = <0x120000 0x10000>;
read-only;
};
partition@130000 {
label = "nvram";
reg = <0x130000 0x100000>;
read-only;
};
concat0: partition@230000 {
label = "concat0";
reg = <0x230000 0xdd0000>;
};
};
};
flash@1 {
compatible = "jedec,spi-nor";
reg = <1>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
concat1: partition@0 {
label = "concat1";
reg = <0x0 0x1000000>;
};
};
};
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
compatible = "pci168c,0033";
reg = <0x0000 0 0 0 0>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
};
};
&eth0 {
status = "okay";
pll-data = <0x1e000000 0x08000101 0x08001313>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
gmac-config {
device = <&gmac>;
rgmii-gmac0 = <1>;
rxd-delay = <0>;
rxdv-delay = <0>;
txen-delay = <0>;
txd-delay = <0>;
};
};