mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
a0b7fef0ff
Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
2262 lines
64 KiB
Makefile
2262 lines
64 KiB
Makefile
#
|
|
# MT7621 Profiles
|
|
#
|
|
|
|
include ./common-sercomm.mk
|
|
include ./common-tp-link.mk
|
|
|
|
DEFAULT_SOC := mt7621
|
|
|
|
KERNEL_DTB += -d21
|
|
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME
|
|
|
|
ifdef CONFIG_LINUX_5_10
|
|
DTS_CPPFLAGS += -DDTS_LEGACY
|
|
endif
|
|
|
|
define Build/arcadyan-trx
|
|
echo -ne "hsqs" > $@.hsqs
|
|
$(eval trx_magic=$(word 1,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/otrx create $@.trx -M $(trx_magic) -f $@ \
|
|
-a 0x20000 -b 0x420000 -f $@.hsqs -a 1000
|
|
mv $@.trx $@
|
|
dd if=/dev/zero bs=1024 count=1 >> $@.tail
|
|
echo -ne "HDR0" | dd of=$@.tail bs=1 seek=$$((0x10c)) count=4 \
|
|
conv=notrunc 2>/dev/null
|
|
dd if=$@.tail >> $@ 2>/dev/null
|
|
rm $@.hsqs $@.tail
|
|
endef
|
|
|
|
define Build/gemtek-trailer
|
|
printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@
|
|
endef
|
|
|
|
define Build/iodata-factory
|
|
$(eval fw_size=$(word 1,$(1)))
|
|
$(eval fw_type=$(word 2,$(1)))
|
|
$(eval product=$(word 3,$(1)))
|
|
$(eval factory_bin=$(word 4,$(1)))
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(fw_size)" ]; then \
|
|
$(CP) $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) $(factory_bin); \
|
|
$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
-r 0x30a -p $(product) -t $(fw_type) \
|
|
-e $(factory_bin) -o $(factory_bin).new; \
|
|
mv $(factory_bin).new $(factory_bin); \
|
|
$(CP) $(factory_bin) $(BIN_DIR)/; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image (actual $$(stat -c%s $@); max $(fw_size))" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/iodata-mstc-header
|
|
( \
|
|
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
|
|
)
|
|
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
|
|
( \
|
|
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
|
|
)
|
|
endef
|
|
|
|
define Build/ubnt-erx-factory-image
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
|
echo '21001:7' > $(1).compat; \
|
|
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
|
|
\
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
|
|
$(MKHASH) md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo "dummy" > $(1).rootfs; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
|
|
\
|
|
$(MKHASH) md5 $(1).rootfs > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
|
|
\
|
|
$(CP) $(1) $(BIN_DIR)/; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image (actual $$(stat -c%s $@); max $(KERNEL_SIZE))" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/zytrx-header
|
|
$(eval board=$(word 1,$(1)))
|
|
$(eval version=$(word 2,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/zytrx -B '$(board)' -v '$(version)' -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/zyxel-nwa-fit
|
|
$(TOPDIR)/scripts/mkits-zyxel-fit.sh \
|
|
$@.its $@ "6b e1 6f e1 ff ff ff ff ff ff"
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Device/dsa-migration
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
|
|
endef
|
|
|
|
define Device/adslr_g7
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ADSLR
|
|
DEVICE_MODEL := G7
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += adslr_g7
|
|
|
|
define Device/afoundry_ew1200
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := AFOUNDRY
|
|
DEVICE_MODEL := EW1200
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ew1200
|
|
endef
|
|
TARGET_DEVICES += afoundry_ew1200
|
|
|
|
define Device/alfa-network_quad-e4g
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Quad-E4G
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 uboot-envtools \
|
|
-wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += quad-e4g
|
|
endef
|
|
TARGET_DEVICES += alfa-network_quad-e4g
|
|
|
|
define Device/ampedwireless_ally_common
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Amped Wireless
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'flashable-initramfs' |\
|
|
edimax-header -s CSYS -m RN68 -f 0x001c0000 -S 0x01100000
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/ampedwireless_ally-r1900k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-R1900K
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-r1900k
|
|
|
|
define Device/ampedwireless_ally-00x19k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-00X19K
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-00x19k
|
|
|
|
define Device/asiarf_ap7621-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-001
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-001
|
|
|
|
define Device/asiarf_ap7621-nv1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-NV1
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-nv1
|
|
|
|
define Device/asus_rp-ac87
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RP-AC87
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware rssileds
|
|
endef
|
|
TARGET_DEVICES += asus_rp-ac87
|
|
|
|
define Device/asus_rt-ac57u
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC57U
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
DEVICE_ALT0_MODEL := RT-AC1200GU
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac57u
|
|
|
|
define Device/asus_rt-ac65p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC65P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac65p
|
|
|
|
define Device/asus_rt-ac85p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC85P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac85p
|
|
|
|
define Device/asus_rt-n56u-b1
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-N56U
|
|
DEVICE_VARIANT := B1
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-n56u-b1
|
|
|
|
define Device/asus_rt-ax53u
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AX53U
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7915e kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ax53u
|
|
|
|
define Device/beeline_smartbox-flash
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Beeline
|
|
DEVICE_MODEL := SmartBox Flash
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4352k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none | arcadyan-trx 0x746f435d | pad-to $$(KERNEL_SIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGES += factory.trx
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware \
|
|
uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += beeline_smartbox-flash
|
|
|
|
define Device/beeline_smartbox-giga
|
|
$(Device/sercomm_dxx)
|
|
IMAGE_SIZE := 24576k
|
|
SERCOMM_HWID := DBE
|
|
SERCOMM_HWVER := 10100
|
|
SERCOMM_SWVER := 1001
|
|
DEVICE_VENDOR := Beeline
|
|
DEVICE_MODEL := SmartBox GIGA
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += beeline_smartbox-giga
|
|
|
|
define Device/buffalo_wsr-1166dhp
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
IMAGE_SIZE := 15936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-1166DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += wsr-1166
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-1166dhp
|
|
|
|
define Device/buffalo_wsr-2533dhpl
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-2533DHPL
|
|
DEVICE_ALT0_VENDOR := Buffalo
|
|
DEVICE_ALT0_MODEL := WSR-2533DHP
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-2533dhpl
|
|
|
|
define Device/buffalo_wsr-600dhp
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-600DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci
|
|
SUPPORTED_DEVICES += wsr-600
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-600dhp
|
|
|
|
define Device/bolt_arion
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := BOLT
|
|
DEVICE_MODEL := Arion
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += bolt_arion
|
|
|
|
define Device/cudy_wr1300
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR1300
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += cudy_wr1300
|
|
|
|
define Device/cudy_wr2100
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR2100
|
|
IMAGE_SIZE := 15872k
|
|
UIMAGE_NAME := R11
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_wr2100
|
|
|
|
define Device/cudy_x6
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32256k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := X6
|
|
UIMAGE_NAME := R13
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
endef
|
|
TARGET_DEVICES += cudy_x6
|
|
|
|
define Device/dlink_dir-8xx-a1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-8xx-r1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
endef
|
|
|
|
define Device/dlink_dir-xx60-a1
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 40960k
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-1960-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-1960
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-1960-a1
|
|
|
|
define Device/dlink_dir-2640-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2640
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2640-a1
|
|
|
|
define Device/dlink_dir-2660-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2660
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2660-a1
|
|
|
|
define Device/dlink_dir-853-a3
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-853
|
|
DEVICE_VARIANT := A3
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-853-a3
|
|
|
|
define Device/dlink_dir-853-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-853
|
|
DEVICE_VARIANT := R1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-853-r1
|
|
|
|
define Device/dlink_dir-860l-b1
|
|
$(Device/dsa-migration)
|
|
$(Device/seama)
|
|
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | relocate-kernel | \
|
|
lzma -a0 | uImage lzma
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-860L
|
|
DEVICE_VARIANT := B1
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += dir-860l-b1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-860l-b1
|
|
|
|
define Device/dlink_dir-867-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-867
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-867-a1
|
|
|
|
define Device/dlink_dir-878-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-878
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-878-a1
|
|
|
|
define Device/dlink_dir-878-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-878
|
|
DEVICE_VARIANT := R1
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-878-r1
|
|
|
|
define Device/dlink_dir-882-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-a1
|
|
|
|
define Device/dlink_dir-882-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := R1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-r1
|
|
|
|
define Device/dual-q_h721
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Dual-Q
|
|
DEVICE_MODEL := H721
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += dual-q_h721
|
|
|
|
define Device/d-team_newifi-d2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += d-team_newifi-d2
|
|
|
|
define Device/d-team_pbr-m1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := PandoraBox
|
|
DEVICE_MODEL := PBR-M1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += pbr-m1
|
|
endef
|
|
TARGET_DEVICES += d-team_pbr-m1
|
|
|
|
define Device/edimax_ra21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RA21S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RA21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020040 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_ra21s
|
|
|
|
define Device/edimax_re23s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15680k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RE23S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RE23S
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_re23s
|
|
|
|
define Device/edimax_rg21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := Gemini AC2600 RG21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020038 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_rg21s
|
|
|
|
define Device/elecom_wrc-1167ghbk2-s
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15488k
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-1167GHBK2-S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
|
|
|
|
define Device/elecom_wrc-gs
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
|
|
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
|
|
define Device/elecom_wrc-1167gs2-b
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1167GS2-B
|
|
ELECOM_HWNAME := WRC-1167GS2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gs2-b
|
|
|
|
define Device/elecom_wrc-1167gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1167GST2
|
|
ELECOM_HWNAME := WRC-1167GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gst2
|
|
|
|
define Device/elecom_wrc-1750gs
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GS
|
|
ELECOM_HWNAME := WRC-1750GS
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gs
|
|
|
|
define Device/elecom_wrc-1750gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1750GST2
|
|
ELECOM_HWNAME := WRC-1750GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gst2
|
|
|
|
define Device/elecom_wrc-1750gsv
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GSV
|
|
ELECOM_HWNAME := WRC-1750GSV
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gsv
|
|
|
|
define Device/elecom_wrc-1900gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1900GST
|
|
ELECOM_HWNAME := WRC-1900GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1900gst
|
|
|
|
define Device/elecom_wrc-2533ghbk-i
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-2533GHBK-I
|
|
IMAGE_SIZE := 9856k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0107002d 8844A2D168B45A2D | \
|
|
elecom-product-header WRC-2533GHBK-I
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk-i
|
|
|
|
define Device/elecom_wrc-2533gs2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-2533GS2
|
|
ELECOM_HWNAME := WRC-2533GS2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gs2
|
|
|
|
define Device/elecom_wrc-2533gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-2533GST
|
|
ELECOM_HWNAME := WRC-2533GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst
|
|
|
|
define Device/elecom_wrc-2533gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-2533GST2
|
|
ELECOM_HWNAME := WRC-2533GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst2
|
|
|
|
define Device/firefly_firewrt
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Firefly
|
|
DEVICE_MODEL := FireWRT
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += firewrt
|
|
endef
|
|
TARGET_DEVICES += firefly_firewrt
|
|
|
|
define Device/gehua_ghl-r-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GeHua
|
|
DEVICE_MODEL := GHL-R-001
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += gehua_ghl-r-001
|
|
|
|
define Device/glinet_gl-mt1300
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-MT1300
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-mt1300
|
|
|
|
define Device/gnubee_gb-pc1
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud One
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc1
|
|
|
|
define Device/gnubee_gb-pc2
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud Two
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc2
|
|
|
|
define Device/hilink_hlk-7621a-evb
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := HiLink
|
|
DEVICE_MODEL := HLK-7621A evaluation board
|
|
DEVICE_PACKAGES += kmod-mt76x2 kmod-usb3
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += hilink_hlk-7621a-evb
|
|
|
|
define Device/hiwifi_hc5962
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32768k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := HiWiFi
|
|
DEVICE_MODEL := HC5962
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += hiwifi_hc5962
|
|
|
|
define Device/humax_e10
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15936k
|
|
DEVICE_VENDOR := HUMAX
|
|
DEVICE_MODEL := E10
|
|
DEVICE_ALT0_VENDOR := HUMAX
|
|
DEVICE_ALT0_MODEL := QUANTUM E10
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | \
|
|
check-size | zip upg -P f013c26cf0a320fb71d03356dcb6bb63
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += humax_e10
|
|
|
|
define Device/iodata_wn-ax1167gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15552k
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
iodata-factory 7864320 4 0x1055 $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AX1167GR
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr
|
|
|
|
define Device/iodata_nand
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := I-O DATA
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 51200k
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
# The OEM webinterface expects an kernel with initramfs which has the uImage
|
|
# header field ih_name.
|
|
# We don't want to set the header name field for the kernel include in the
|
|
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
|
|
# webinterface. It will soft-brick the board.
|
|
|
|
define Device/iodata_wn-ax1167gr2
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX1167GR2
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr2
|
|
|
|
define Device/iodata_wn-ax2033gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX2033GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax2033gr
|
|
|
|
define Device/iodata_wn-dx1167r
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1167R
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1167r
|
|
|
|
define Device/iodata_wn-dx1200gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1200GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1200gr
|
|
|
|
define Device/iodata_wn-dx2033gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX2033GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XID.0)b30' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx2033gr
|
|
|
|
define Device/iodata_wn-gx300gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7616k
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-GX300GR
|
|
DEVICE_PACKAGES := kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-gx300gr
|
|
|
|
define Device/iodata_wnpr2600g
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WNPR2600G
|
|
IMAGE_SIZE := 13952k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0104003a 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wnpr2600g
|
|
|
|
define Device/iptime_a3002mesh
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a3002me
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3002MESH
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iptime_a3002mesh
|
|
|
|
define Device/iptime_a3004ns-dual
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a3004nd
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3004NS-dual
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76x2 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a3004ns-dual
|
|
|
|
define Device/iptime_a3004t
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UIMAGE_NAME := a3004t
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3004T
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_a3004t
|
|
|
|
define Device/iptime_a6004ns-m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a6004nm
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A6004NS-M
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a6004ns-m
|
|
|
|
define Device/iptime_a6ns-m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a6nm
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A6ns-M
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a6ns-m
|
|
|
|
define Device/iptime_a8004t
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a8004t
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A8004T
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_a8004t
|
|
|
|
define Device/iptime_ax2004m
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 121344k
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size | iptime-crc32 ax2004m
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := AX2004M
|
|
DEVICE_PACKAGES := kmod-mt7915e kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_ax2004m
|
|
|
|
define Device/iptime_t5004
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
UIMAGE_NAME := t5004
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := T5004
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += iptime_t5004
|
|
|
|
define Device/jcg_jhr-ac876m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := JHR-AC876M
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += jcg_jhr-ac876m
|
|
|
|
define Device/jcg_q20
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 91136k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Q20
|
|
DEVICE_PACKAGES := kmod-mt7915e uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += jcg_q20
|
|
|
|
define Device/jcg_y2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Y2
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += jcg_y2
|
|
|
|
define Device/lenovo_newifi-d1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += newifi-d1
|
|
endef
|
|
TARGET_DEVICES += lenovo_newifi-d1
|
|
|
|
define Device/linksys_e5600
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := E5600
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | gemtek-trailer
|
|
endef
|
|
TARGET_DEVICES += linksys_e5600
|
|
|
|
define Device/linksys_ea7xxx
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 36864k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
endef
|
|
|
|
define Device/linksys_ea6350-v4
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA6350
|
|
DEVICE_VARIANT := v4
|
|
LINKSYS_HWNAME := EA6350
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += linksys_ea6350-v4
|
|
|
|
define Device/linksys_ea7300-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA7300
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v1
|
|
|
|
define Device/linksys_ea7300-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7300v2
|
|
DEVICE_PACKAGES += kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v2
|
|
|
|
define Device/linksys_ea7500-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7500
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7500v2
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7500-v2
|
|
|
|
define Device/linksys_ea8100-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA8100
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA8100
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8100-v1
|
|
|
|
define Device/linksys_ea8100-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA8100
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA8100v2
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8100-v2
|
|
|
|
define Device/linksys_re6500
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := RE6500
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
SUPPORTED_DEVICES += re6500
|
|
endef
|
|
TARGET_DEVICES += linksys_re6500
|
|
|
|
define Device/mediatek_ap-mt7621a-v60
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Mediatek
|
|
DEVICE_MODEL := AP-MT7621A-V60 EVB
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += mediatek_ap-mt7621a-v60
|
|
|
|
define Device/mediatek_mt7621-eval-board
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 15104k
|
|
DEVICE_VENDOR := MediaTek
|
|
DEVICE_MODEL := MT7621 EVB
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mt7621
|
|
endef
|
|
TARGET_DEVICES += mediatek_mt7621-eval-board
|
|
|
|
define Device/MikroTik
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := MikroTik
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_PACKAGES := kmod-usb3
|
|
KERNEL_NAME := vmlinuz
|
|
KERNEL := kernel-bin | append-dtb-elf
|
|
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | \
|
|
append-metadata
|
|
endef
|
|
|
|
define Device/mikrotik_routerboard-750gr3
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 750Gr3
|
|
DEVICE_PACKAGES += -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rb750gr3
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-750gr3
|
|
|
|
define Device/mikrotik_routerboard-760igs
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 760iGS
|
|
DEVICE_PACKAGES += kmod-sfp -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-760igs
|
|
|
|
define Device/mikrotik_routerboard-m11g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M11G
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm11g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m11g
|
|
|
|
define Device/mikrotik_routerboard-m33g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M33G
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm33g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m33g
|
|
|
|
define Device/mqmaker_witi
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := MQmaker
|
|
DEVICE_MODEL := WiTi
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
|
|
endef
|
|
TARGET_DEVICES += mqmaker_witi
|
|
|
|
define Device/mtc_wr1201
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := MTC
|
|
DEVICE_MODEL := Wireless Router WR1201
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += mtc_wr1201
|
|
|
|
define Device/mts_wg430223
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := MTS
|
|
DEVICE_MODEL := WG430223
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4352k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none | arcadyan-trx 0x53485231 | pad-to $$(KERNEL_SIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGES += factory.trx
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += mts_wg430223
|
|
|
|
define Device/netgear_ex6150
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := EX6150
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
|
|
IMAGE_SIZE := 14848k
|
|
IMAGES += factory.chk
|
|
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6150
|
|
|
|
define Device/netgear_sercomm_nand
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img kernel.bin rootfs.bin
|
|
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
|
|
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
|
|
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-ubi | check-size
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
|
|
define Device/netgear_r6220
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6220
|
|
SERCOMM_HWNAME := R6220
|
|
SERCOMM_HWID := AYA
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0086
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
SUPPORTED_DEVICES += r6220
|
|
endef
|
|
TARGET_DEVICES += netgear_r6220
|
|
|
|
|
|
define Device/netgear_r6260
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6260
|
|
SERCOMM_HWNAME := R6260
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6260
|
|
|
|
define Device/netgear_r6350
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6350
|
|
SERCOMM_HWNAME := R6350
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6350
|
|
|
|
define Device/netgear_r6700-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6700
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := Nighthawk AC2400
|
|
DEVICE_ALT0_VARIANT := v1
|
|
DEVICE_ALT1_VENDOR := NETGEAR
|
|
DEVICE_ALT1_MODEL := Nighthawk AC2100
|
|
DEVICE_ALT1_VARIANT := v1
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6700-v2
|
|
|
|
define Device/netgear_r6800
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6800
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0062
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6800
|
|
|
|
define Device/netgear_r6850
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6850
|
|
SERCOMM_HWNAME := R6850
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6850
|
|
|
|
define Device/netgear_r6900-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6900
|
|
DEVICE_VARIANT := v2
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6900-v2
|
|
|
|
define Device/netgear_r7200
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R7200
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r7200
|
|
|
|
define Device/netgear_r7450
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R7450
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r7450
|
|
|
|
define Device/netgear_wac104
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC104
|
|
SERCOMM_HWNAME := WAC104
|
|
SERCOMM_HWID := CAY
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0006
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += netgear_wac104
|
|
|
|
define Device/netgear_wac124
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC124
|
|
SERCOMM_HWNAME := WAC124
|
|
SERCOMM_HWID := CTL
|
|
SERCOMM_HWVER := A003
|
|
SERCOMM_SWVER := 0x0402
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_wac124
|
|
|
|
define Device/netgear_wax202
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := WAX202
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
NETGEAR_ENC_MODEL := WAX202
|
|
NETGEAR_ENC_REGION := US
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 38912k
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
append-squashfs4-fakeroot
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | netgear-encrypted-factory
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += netgear_wax202
|
|
|
|
define Device/netgear_wndr3700-v5
|
|
$(Device/dsa-migration)
|
|
$(Device/netgear_sercomm_nor)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v5
|
|
SERCOMM_HWNAME := WNDR3700v5
|
|
SERCOMM_HWID := AYB
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1054
|
|
SERCOMM_PAD := 320k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += wndr3700v5
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v5
|
|
|
|
define Device/netis_wf2881
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
UIMAGE_NAME := WF2881_0.0.00
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2881 | uImage lzma
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := NETIS
|
|
DEVICE_MODEL := WF2881
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += netis_wf2881
|
|
|
|
define Device/oraybox_x3a
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15360k
|
|
DEVICE_VENDOR := OrayBox
|
|
DEVICE_MODEL := X3A
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += oraybox_x3a
|
|
|
|
define Device/phicomm_k2p
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15744k
|
|
DEVICE_VENDOR := Phicomm
|
|
DEVICE_MODEL := K2P
|
|
DEVICE_ALT0_VENDOR := Phicomm
|
|
DEVICE_ALT0_MODEL := KE 2P
|
|
SUPPORTED_DEVICES += k2p
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += phicomm_k2p
|
|
|
|
define Device/planex_vr500
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := Planex
|
|
DEVICE_MODEL := VR500
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += vr500
|
|
endef
|
|
TARGET_DEVICES += planex_vr500
|
|
|
|
define Device/raisecom_msg1500-x-00
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := RAISECOM
|
|
DEVICE_MODEL := MSG1500
|
|
DEVICE_VARIANT := X.00
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += raisecom_msg1500-x-00
|
|
|
|
define Device/renkforce_ws-wn530hp3-a
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Renkforce
|
|
DEVICE_MODEL := WS-WN530HP3-A
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 65536 | append-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += renkforce_ws-wn530hp3-a
|
|
|
|
define Device/samknows_whitebox-v8
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := SamKnows
|
|
DEVICE_MODEL := Whitebox 8
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += sk-wb8
|
|
endef
|
|
TARGET_DEVICES += samknows_whitebox-v8
|
|
|
|
define Device/sercomm_na502
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20480k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
DEVICE_VENDOR := SERCOMM
|
|
DEVICE_MODEL := NA502
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += sercomm_na502
|
|
|
|
define Device/sercomm_na502s
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20971520
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
DEVICE_VENDOR := SERCOMM
|
|
DEVICE_MODEL := NA502S
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3 kmod-usb-serial \
|
|
kmod-usb-serial-xr_usb_serial_common
|
|
endef
|
|
TARGET_DEVICES += sercomm_na502s
|
|
|
|
define Device/storylink_sap-g3200u3
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := STORYLiNK
|
|
DEVICE_MODEL := SAP-G3200U3
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += sap-g3200u3
|
|
endef
|
|
TARGET_DEVICES += storylink_sap-g3200u3
|
|
|
|
define Device/telco-electronics_x1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Telco Electronics
|
|
DEVICE_MODEL := X1
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76
|
|
endef
|
|
TARGET_DEVICES += telco-electronics_x1
|
|
|
|
define Device/tenbay_t-mb5eu-v01
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Tenbay
|
|
DEVICE_MODEL := T-MB5EU-V01
|
|
DEVICE_DTS_CONFIG := config@1
|
|
DEVICE_PACKAGES += kmod-mt7915e kmod-usb3
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 15808k
|
|
SUPPORTED_DEVICES += mt7621-dm2-t-mb5eu-v01-nor
|
|
endef
|
|
TARGET_DEVICES += tenbay_t-mb5eu-v01
|
|
|
|
define Device/thunder_timecloud
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Thunder
|
|
DEVICE_MODEL := Timecloud
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += timecloud
|
|
endef
|
|
TARGET_DEVICES += thunder_timecloud
|
|
|
|
define Device/totolink_a7000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8340R1C-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := A7000R
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += totolink_a7000r
|
|
|
|
define Device/totolink_x5000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8343R-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := X5000R
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
endef
|
|
TARGET_DEVICES += totolink_x5000r
|
|
|
|
define Device/tplink_archer-a6-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer A6
|
|
DEVICE_VARIANT := V3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := ARCHER-A6-V3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-a6-v3
|
|
|
|
define Device/tplink_archer-c6-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer C6
|
|
DEVICE_VARIANT := V3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := ARCHER-C6-V3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-c6-v3
|
|
|
|
define Device/tplink_archer-c6u-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer C6U
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 \
|
|
kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
TPLINK_BOARD_ID := ARCHER-C6U-V1
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-c6u-v1
|
|
|
|
define Device/tplink_eap235-wall-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := EAP235-Wall
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := EAP235-WALL-V1
|
|
IMAGE_SIZE := 13440k
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
|
|
pad-extra 128
|
|
endef
|
|
TARGET_DEVICES += tplink_eap235-wall-v1
|
|
|
|
define Device/tplink_eap615-wall-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := EAP615-Wall
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
TPLINK_BOARD_ID := EAP615-WALL-V1
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
IMAGE_SIZE := 13248k
|
|
endef
|
|
TARGET_DEVICES += tplink_eap615-wall-v1
|
|
|
|
define Device/tplink_re350-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE350
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
TPLINK_BOARD_ID := RE350-V1
|
|
IMAGE_SIZE := 6016k
|
|
SUPPORTED_DEVICES += re350-v1
|
|
endef
|
|
TARGET_DEVICES += tplink_re350-v1
|
|
|
|
define Device/tplink_re500-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE500
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE500-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re500-v1
|
|
|
|
define Device/tplink_re650-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE650
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE650-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re650-v1
|
|
|
|
define Device/tplink_re650-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE650
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE650-V2
|
|
IMAGE_SIZE := 7994k
|
|
endef
|
|
TARGET_DEVICES += tplink_re650-v2
|
|
|
|
define Device/tplink_tl-wpa8631p-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := TL-WPA8631P
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := TL-WPA8631P-V3
|
|
IMAGE_SIZE := 7232k
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-wpa8631p-v3
|
|
|
|
define Device/ubnt_edgerouter_common
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
IMAGE_SIZE := 256768k
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 3145728
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES += -wpad-basic-wolfssl
|
|
endef
|
|
|
|
define Device/ubnt_edgerouter-x
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X
|
|
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x
|
|
|
|
define Device/ubnt_edgerouter-x-sfp
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X SFP
|
|
DEVICE_ALT0_VENDOR := Ubiquiti
|
|
DEVICE_ALT0_MODEL := EdgePoint R6
|
|
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
|
|
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x-sfp
|
|
|
|
define Device/ubnt_unifi-6-lite
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi 6 Lite
|
|
DEVICE_DTS_CONFIG := config@1
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915e
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 15424k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-6-lite
|
|
|
|
define Device/ubnt_unifi-nanohd
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi nanoHD
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
IMAGE_SIZE := 15552k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-nanohd
|
|
|
|
define Device/ubnt_usw-flex
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi Switch Flex
|
|
DEVICE_DTS_CONFIG := config@1
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 7360k
|
|
endef
|
|
TARGET_DEVICES += ubnt_usw-flex
|
|
|
|
define Device/unielec_u7621-01-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-01
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-01-16m
|
|
|
|
define Device/unielec_u7621-06-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-16m
|
|
|
|
define Device/unielec_u7621-06-64m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 64M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-64m
|
|
|
|
define Device/wavlink_wl-wn531a6
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WL-WN531A6
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += wavlink_wl-wn531a6
|
|
|
|
define Device/wavlink_wl-wn533a8
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WL-WN533A8
|
|
KERNEL_INITRAMFS_SUFFIX := -WN533A8$$(KERNEL_SUFFIX)
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += wavlink_wl-wn533a8
|
|
|
|
define Device/wevo_11acnas
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := 11AC NAS Router
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += 11acnas
|
|
endef
|
|
TARGET_DEVICES += wevo_11acnas
|
|
|
|
define Device/wevo_w2914ns-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := W2914NS-V2(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := W2914NS
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += w2914nsv2
|
|
endef
|
|
TARGET_DEVICES += wevo_w2914ns-v2
|
|
|
|
define Device/winstars_ws-wn583a6
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Winstars
|
|
DEVICE_MODEL := WS-WN583A6
|
|
DEVICE_ALT0_VENDOR := Gemeita
|
|
DEVICE_ALT0_MODEL := AC2100
|
|
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += winstars_ws-wn583a6
|
|
|
|
define Device/xiaomi_nand_separate
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += kernel1.bin rootfs0.bin
|
|
IMAGE/kernel1.bin := append-kernel
|
|
IMAGE/rootfs0.bin := append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-3g
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 3G
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g
|
|
|
|
define Device/xiaomi_mi-router-3g-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3G
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += xiaomi,mir3g-v2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g-v2
|
|
|
|
define Device/xiaomi_mi-router-3-pro
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE:= 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 255488k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3 Pro
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += xiaomi,mir3p
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3-pro
|
|
|
|
define Device/xiaomi_mi-router-4
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 4
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4
|
|
|
|
define Device/xiaomi_mi-router-4a-gigabit
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4A
|
|
DEVICE_VARIANT := Gigabit Edition
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
|
|
|
|
define Device/xiaomi_mi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-ac2100
|
|
|
|
define Device/xiaomi_mi-router-cr660x
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 128512k
|
|
IMAGES += firmware.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/firmware.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES += kmod-mt7915e uboot-envtools
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-cr6606
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6606
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6606
|
|
|
|
define Device/xiaomi_mi-router-cr6608
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6608
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6608
|
|
|
|
define Device/xiaomi_mi-router-cr6609
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6609
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6609
|
|
|
|
define Device/xiaomi_redmi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Redmi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_redmi-router-ac2100
|
|
|
|
define Device/xiaoyu_xy-c5
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := XiaoYu
|
|
DEVICE_MODEL := XY-C5
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += xiaoyu_xy-c5
|
|
|
|
define Device/xzwifi_creativebox-v1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := CreativeBox
|
|
DEVICE_MODEL := v1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += xzwifi_creativebox-v1
|
|
|
|
define Device/youhua_wr1200js
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := YouHua
|
|
DEVICE_MODEL := WR1200JS
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += youhua_wr1200js
|
|
|
|
define Device/youku_yk-l2
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Youku
|
|
DEVICE_MODEL := YK-L2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += youku_yk-l2
|
|
|
|
define Device/yuncore_ax820
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15808k
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := AX820
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
endef
|
|
TARGET_DEVICES += yuncore_ax820
|
|
|
|
define Device/zbtlink_zbt-we1326
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE1326
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620
|
|
SUPPORTED_DEVICES += zbt-we1326
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we1326
|
|
|
|
define Device/zbtlink_zbt-we3526
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE3526
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we3526
|
|
|
|
define Device/zbtlink_zbt-wg1602-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1602
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-16m
|
|
|
|
define Device/zbtlink_zbt-wg1608-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1608
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1608-16m
|
|
|
|
define Device/zbtlink_zbt-wg2626
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG2626
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg2626
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg2626
|
|
|
|
define Device/zbtlink_zbt-wg3526-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
|
|
|
|
define Device/zbtlink_zbt-wg3526-32m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 32M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
|
|
|
|
define Device/zio_freezio
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ZIO
|
|
DEVICE_MODEL := FREEZIO
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zio_freezio
|
|
|
|
define Device/zyxel_nr7101
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NR7101
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 uboot-envtools kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) 9.99(ABUV.9)$$(VERSION_DIST)-recovery
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_nr7101
|
|
|
|
define Device/zyxel_nwa-ax
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ZyXEL
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 8192k
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_PACKAGES := kmod-mt7915e uboot-envtools zyxel-bootconfig
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += factory.bin ramboot-factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | zyxel-nwa-fit
|
|
IMAGE/ramboot-factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/zyxel_nwa50ax
|
|
$(Device/zyxel_nwa-ax)
|
|
DEVICE_MODEL := NWA50AX
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa50ax
|
|
|
|
define Device/zyxel_nwa55axe
|
|
$(Device/zyxel_nwa-ax)
|
|
DEVICE_MODEL := NWA55AXE
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa55axe
|
|
|
|
define Device/zyxel_wap6805
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := WAP6805
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | uimage-padhdr 160
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_wap6805
|