mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
e4ce3109f2
The node pinctrl0 is already set up in the SOC DTSI files, but defined again as member of pinctrl in most of the device DTS(I) files. This patch removes this redundancy for the entire ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
148 lines
2.3 KiB
Plaintext
148 lines
2.3 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "rt2880.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc";
|
|
model = "D-Link DAP-1522 A1";
|
|
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-failsafe = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
};
|
|
|
|
cfi@bc400000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0xbc400000 0x800000>;
|
|
bank-width = <2>;
|
|
device-width = <2>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "uboot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@30000 {
|
|
label = "factory";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
compatible = "wrg";
|
|
label = "firmware";
|
|
reg = <0x40000 0x3a0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
rtl8366s {
|
|
compatible = "realtek,rtl8366s";
|
|
gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
|
|
gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
bridge {
|
|
label = "bridge";
|
|
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "dap-1522-a1:blue:wps";
|
|
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
ap {
|
|
label = "dap-1522-a1:blue:ap";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sta {
|
|
label = "dap-1522-a1:red:sta";
|
|
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_status: status {
|
|
label = "dap-1522-a1:blue:status";
|
|
gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
ralink,group = "i2c", "uartlite", "pci";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x2004>;
|
|
|
|
port@0 {
|
|
mediatek,fixed-link = <1000 1 1 1>;
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
phy-mode = "mii";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0x2000>;
|
|
};
|