mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 18:19:02 +00:00
a8898f1a11
The hack-patch which introduced the "at803x-disable-smarteee" for disabling SmartEEE did in fact not disable SmartEEE but rather disabled 802.3az "standard" EEE. This can be done by using the upstream properties "eee-broken-100tx" and "eee-broken-1000t". EEE is then disabled by the PHY subsystem. Tested on devolo WiFi pro 1200e. Signed-off-by: David Bauer <mail@david-bauer.net>
160 lines
2.4 KiB
Plaintext
160 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9557.dtsi"
|
|
|
|
/ {
|
|
compatible = "ocedo,koala", "qca,qca9557";
|
|
model = "OCEDO Koala";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "koala:green:power";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wifi2 {
|
|
label = "koala:yellow:wlan2";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wifi5 {
|
|
label = "koala:red:wlan58";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
led_system: system {
|
|
label = "koala:blue:sys";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
clocks = <&extosc>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x740000>;
|
|
};
|
|
|
|
partition@790000 {
|
|
label = "vendor";
|
|
reg = <0x790000 0x740000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@ed0000 {
|
|
label = "data";
|
|
reg = <0xed0000 0x110000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "id";
|
|
reg = <0xfe0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x06>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
eee-broken-100tx;
|
|
eee-broken-1000t;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x00>;
|
|
|
|
phy-handle = <&phy5>;
|
|
phy-mode = "rgmii-rxid";
|
|
|
|
pll-data = <0x8e000000 0x80000101 0x80001313>;
|
|
};
|