ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-02-25 10:52:48 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
openwrt/target/linux/ipq806x/image/Makefile
Robert Marko b23a4eea12 ipq806x: add Edgecore ECW5410 support 
This patch adds support for the Edgecore ECW5410 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.

Installation instructions:
Through stock firmware or initramfs.

1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>

This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0

Note

Initramfs:
1.  Connect to console
2.  Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1

You need to interrupt the bootloader after rebooting and run:
run altbootcmd

This will switch your active rootfs partition to one you wrote to and boot from it.

So if rootfs1 is active, then it will change it to rootfs2.

This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.

5. Transfer sysupgrade image
6. Flash with sysupgrade -n.

Note that sysupgrade will write the image to rootfs partition that is not currently in use.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: maurerr <mariusd84@gmail.com>
2021-09-01 08:06:59 +00:00

347 lines
9.5 KiB
Makefile
Raw Blame History

# Copyright (c) 2014 The Linux Foundation. All rights reserved.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += TPLINK_BOARD_ID
define Build/buffalo-rootfs-cksum
( \
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
) >> $@
endef
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR = 0x42208000
DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/LegacyImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
UBINIZE_OPTS := -E 5
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | append-metadata
endef
define Device/TpSafeImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
TPLINK_BOARD_ID :=
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata
endef
define Device/ZyXELImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$(KERNEL_SIZE)
KERNEL_NAME := zImage
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/buffalo_wxr-2533dhp
$(call Device/LegacyImage)
SOC := qcom-ipq8064
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WXR-2533DHP
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += buffalo_wxr-2533dhp
define Device/compex_wpq864
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPQ864
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq8064
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpq864
define Device/linksys_ea7500-v1
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to $$$$(PAGESIZE)
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea7500-v1
define Device/edgecore_ecw5410
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_TITLE := Edgecore ECW5410
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS := qcom-ipq8068-ecw5410
DEVICE_DTS_CONFIG := config@v2.0-ap160
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-edgecore_ecw5410
endef
TARGET_DEVICES += edgecore_ecw5410
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8500
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
BOARD_NAME := ea8500
SUPPORTED_DEVICES += ea8500
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea8500
define Device/nec_wg2600hp
$(call Device/LegacyImage)
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG2600HP
SOC := qcom-ipq8064
BLOCKSIZE := 64k
BOARD_NAME := wg2600hp
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += nec_wg2600hp
define Device/netgear_d7800
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 D7800
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := D7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := d7800
SUPPORTED_DEVICES += d7800
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += netgear_d7800
define Device/netgear_r7500
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500
SUPPORTED_DEVICES += r7500
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500
define Device/netgear_r7500v2
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v2
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500v2
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500v2
SUPPORTED_DEVICES += r7500v2
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500v2
define Device/netgear_r7800
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4S R7800
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7800
SUPPORTED_DEVICES += r7800
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += netgear_r7800
define Device/qcom_ipq8064-ap148
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := standard
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES += ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148
define Device/qcom_ipq8064-ap148-legacy
$(call Device/LegacyImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := legacy
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
define Device/qcom_ipq8064-ap161
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP161
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap161
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap161
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap161
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := DB149
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-db149
KERNEL_INSTALL := 1
BOARD_NAME := db149
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-db149
define Device/tplink_c2600
$(call Device/TpSafeImage)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer C2600
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := c2600
SUPPORTED_DEVICES += c2600
TPLINK_BOARD_ID := C2600
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += tplink_c2600
define Device/tplink_vr2600v
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer VR2600v
DEVICE_VARIANT := v1
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SIZE := 3072k
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := vr2600v
SUPPORTED_DEVICES += vr2600v
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += tplink_vr2600v
define Device/zyxel_nbg6817
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6817
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
RAS_BOARD := NBG6817
RAS_ROOTFS_SIZE := 20934k
RAS_VERSION := "V1.99(OWRT.9999)C0"
SUPPORTED_DEVICES += nbg6817
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
$(call Device/ZyXELImage)
endef
TARGET_DEVICES += zyxel_nbg6817
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink