This repository is a mirror of https://git.openwrt.org/openwrt/openwrt.git It is for reference only and is not active for check-ins. We will continue to accept Pull Requests here. They will be merged via staging trees then into openwrt.git.
Go to file
George Witt 9b33645566 ipq807x: add support for TP-Link EAP660 HD v1
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)

Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
   and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
   openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
   serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
   # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   # bootm
   You may need to type Ctrl+C and Enter before running these commands
   to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
   to be installed (check IP address):
   $ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
   # cd /tmp
   # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.

Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-09-08 12:01:19 +02:00
.devcontainer/ci-env devcontainer: Add development environment for gihub codespace 2023-10-30 23:34:26 +01:00
.github Revert "CI: update actions/labeler to v5" 2024-08-26 23:29:06 +02:00
config kernel: Activate POSIX ACL for f2fs, jffs2 and tmpfs 2024-09-06 23:25:55 +02:00
include kernel: bump 6.1 to 6.1.108 2024-09-06 22:38:55 +02:00
LICENSES LICENSES: include all used licenses in LICENSES directory 2021-02-14 19:21:38 +01:00
package ipq807x: add support for TP-Link EAP660 HD v1 2024-09-08 12:01:19 +02:00
scripts scripts/download.pl: fix broken link for KERNEL projects 2024-06-19 14:30:06 +02:00
target ipq807x: add support for TP-Link EAP660 HD v1 2024-09-08 12:01:19 +02:00
toolchain toolchain: binutils: add support for 2.43 2024-08-16 20:10:38 +08:00
tools tools: libtool: do not symlink files in bootstrap 2024-08-29 20:04:02 +02:00
.gitattributes add .gitattributes to prevent the git autocrlf option from messing with CRLF/LF in files 2012-05-08 13:30:49 +00:00
.gitignore gitignore: ignore local APK keys 2024-05-17 22:03:06 +03:00
BSDmakefile build: use SPDX license tags 2021-02-05 14:54:47 +01:00
Config.in build: scripts/config - update to kconfig-v5.14 2022-02-19 13:10:01 +01:00
COPYING COPYING: add COPYING file to specify project licenses 2021-02-14 19:21:38 +01:00
feeds.conf.default Revert "feeds: use git-src-full to allow Git versioning" 2023-05-23 14:38:55 +02:00
Makefile build: include tests/Makefile if available 2024-06-17 17:51:31 +02:00
README.md README: replace "MacOSX" with "macOS" 2024-04-01 18:46:30 +02:00
rules.mk build: let HOST_CXXFLAGS default to HOST_CFLAGS 2024-07-08 08:49:43 +02:00

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Download

Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.

If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.

An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:

Development

To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

  • LuCI Web Interface: Modern and modular interface to control the device via a web browser.

  • OpenWrt Packages: Community repository of ported packages.

  • OpenWrt Routing: Packages specifically focused on (mesh) routing.

  • OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on oftc.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0