openwrt/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
INAGAKI Hiroshi bb6d11e534 ath79: add aliases to qca955x.dtsi for uart0/1
Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to
qca955x.dtsi, to enable uart1 on Linux Kernel.

without this:

[    0.342915] ar933x-uart 18500000.uart: unable to get alias id, err=-19

Additionally, remove "serial0 = &uart;" alias from QCA955x device
dts/dtsi files.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-03-08 17:35:01 +01:00

230 lines
4.0 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca955x.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
compatible = "openmesh,om5p-ac-v1", "qca,qca9558";
model = "OpenMesh OM5P-AC v1";
chosen {
/delete-property/ bootargs;
};
aliases {
led-boot = &led_power_blue;
led-failsafe = &led_power_blue;
led-running = &led_power_blue;
led-upgrade = &led_power_blue;
label-mac-device = &eth0;
};
leds {
compatible = "gpio-leds";
led_power_blue: power_blue {
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wan_blue {
function = LED_FUNCTION_WAN;
color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
};
lan_blue {
function = LED_FUNCTION_LAN;
color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
wifi_green {
label = "green:wifi";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wifi_yellow {
label = "yellow:wifi";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
};
wifi_red {
label = "red:wifi";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
};
};
i2c {
compatible = "i2c-gpio";
gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */
&gpio 12 GPIO_ACTIVE_HIGH /* scl */
>;
#address-cells = <1>;
#size-cells = <0>;
i2c-gpio,scl-open-drain;
i2c-gpio,sda-open-drain;
tmp423a@4c {
compatible = "ti,tmp423";
reg = <0x4c>;
};
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
hw_algo = "toggle";
/* hw_margin_ms is actually 300s but driver limits it to 60s */
hw_margin_ms = <60000>;
always-running;
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
/* partitions are passed via bootloader */
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
label = "custom";
reg = <0x050000 0x060000>;
read-only;
};
partition@b0000 {
label = "inactive";
reg = <0x0b0000 0x7a0000>;
};
partition@850000 {
label = "inactive2";
reg = <0x850000 0x7a0000>;
};
art: partition@ff0000 {
label = "ART";
reg = <0xff0000 0x010000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_art_0: macaddr@0 {
compatible = "mac-base";
reg = <0x0 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_art_6: macaddr@6 {
reg = <0x6 0x6>;
};
cal_art_5000: calibration@5000 {
reg = <0x5000 0x844>;
};
};
};
};
};
};
&mdio0 {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
eee-broken-100tx;
eee-broken-1000t;
};
phy2: ethernet-phy@2 {
reg = <2>;
eee-broken-100tx;
eee-broken-1000t;
at803x-override-sgmii-link-check;
};
};
&eth0 {
status = "okay";
pll-data = <0x82000101 0x80000101 0x80001313>;
nvmem-cells = <&macaddr_art_0 0>;
nvmem-cell-names = "mac-address";
phy-mode = "rgmii-id";
phy-handle = <&phy1>;
gmac-config {
device = <&gmac>;
rgmii-enabled = <1>;
rxd-delay = <3>;
rxdv-delay = <3>;
txd-delay = <0>;
txen-delay = <0>;
};
};
&eth1 {
status = "okay";
pll-data = <0x03000101 0x80000101 0x80001313>;
nvmem-cells = <&macaddr_art_6>;
nvmem-cell-names = "mac-address";
qca955x-sgmii-fixup;
phy-handle = <&phy2>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
nvmem-cells = <&macaddr_art_0 2>;
nvmem-cell-names = "mac-address";
};
&pcie1 {
status = "okay";
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&cal_art_5000>, <&macaddr_art_0 16>;
nvmem-cell-names = "calibration", "mac-address";
};
};