mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 02:29:01 +00:00
301bc3290d
As evidenced here[1] the device MAC address can be stored at a random offset in the hard_config partition. Rely on sysfs to update the MAC address correctly. To match sticker and vendor OS behavior, WAN MAC is set to the device base MAC and LAN MAC is incremented from that. Note: this will trigger a harmless kernel message during boot: ag71xx 19000000.eth: invalid MAC address, using random address There is no clean workaround to prevent this message from being emitted. [1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021 Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
179 lines
2.6 KiB
Plaintext
179 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-922uags-5hpacd", "qca,qca9558";
|
|
model = "MikroTik RouterBOARD 922UAGS-5HPacD";
|
|
|
|
aliases {
|
|
led-boot = &led_user;
|
|
led-failsafe = &led_user;
|
|
led-upgrade = &led_user;
|
|
serial0 = &uart;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_user: user {
|
|
label = "mikrotik:green:user";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ath10k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan5g {
|
|
label = "mikrotik:green:wlan5g";
|
|
gpios = <&ath10k 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
gpio-export {
|
|
compatible = "gpio-export";
|
|
|
|
gpio_usb_power {
|
|
gpio-export,name = "mikrotik:power:usb";
|
|
gpio-export,output = <0>;
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
gpio_nand_power {
|
|
gpio-export,name = "mikrotik:power:nand";
|
|
gpio-export,output = <0>;
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy4>;
|
|
pll-data = <0x8f000000 0xa0000101 0xa0001313>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
rgmii-enabled = <1>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "routerboot";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config: hard_config {
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
nand-ecc-mode = "soft";
|
|
qca,nand-swap-dma;
|
|
qca,nand-scan-fixup;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "booter";
|
|
reg = <0x0000000 0x0040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "kernel";
|
|
reg = <0x0040000 0x03c0000>;
|
|
};
|
|
|
|
partition@400000 {
|
|
label = "ubi";
|
|
reg = <0x0400000 0x7c00000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
ath10k: wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|