mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 17:48:58 +00:00
aa4a33ac62
This board was previously supported in ar71xx as 'RUT9XX'. The difference between that and the other RUT955 board already supported in ath79 is that instead of the SPI shift registers driving the LEDs and digital outputs that model got an I2C GPIO expander instead. To support LEDs during early boot and interrupt-driven digital inputs, I2C support as well as support for PCA953x has to be built-in and cannot be kernel modules, hence select those symbols for ath79/generic. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by PCA9539) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector Serial console (/dev/ttyS0) pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1". Signed-off-by: Daniel Golle <daniel@makrotopia.org>
30 lines
674 B
Plaintext
30 lines
674 B
Plaintext
CONFIG_AT803X_PHY=y
|
|
CONFIG_BCM_NET_PHYLIB=y
|
|
CONFIG_BROADCOM_PHY=y
|
|
CONFIG_GPIO_PCA953X=y
|
|
CONFIG_GPIO_PCA953X_IRQ=y
|
|
CONFIG_GPIO_WATCHDOG=y
|
|
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
|
CONFIG_I2C=y
|
|
CONFIG_I2C_ALGOBIT=y
|
|
CONFIG_I2C_CHARDEV=y
|
|
CONFIG_I2C_GPIO=y
|
|
CONFIG_INTEL_XWAY_PHY=y
|
|
CONFIG_IP17XX_PHY=y
|
|
CONFIG_LEDS_RESET=y
|
|
CONFIG_MARVELL_PHY=y
|
|
CONFIG_MICREL_PHY=y
|
|
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-3
|
|
CONFIG_MTD_REDBOOT_PARTS=y
|
|
CONFIG_MTD_SPLIT_EVA_FW=y
|
|
CONFIG_PHY_AR7100_USB=y
|
|
CONFIG_PHY_AR7200_USB=y
|
|
CONFIG_REGULATOR=y
|
|
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
|
CONFIG_RTL8366RB_PHY=y
|
|
CONFIG_RTL8366S_PHY=y
|
|
CONFIG_RTL8366_SMI=y
|
|
CONFIG_RTL8367_PHY=y
|
|
CONFIG_VITESSE_PHY=y
|
|
CONFIG_WATCHDOG_CORE=y
|