mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
97f5617259
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
129 lines
2.7 KiB
Plaintext
129 lines
2.7 KiB
Plaintext
#
|
|
# Copyright (C) 2011-2014 OpenWrt.org
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
alfa-network,ap121f|\
|
|
alfa-network,ap121fe|\
|
|
alfa-network,n2q|\
|
|
alfa-network,n5q|\
|
|
alfa-network,pi-wifi4|\
|
|
alfa-network,r36a|\
|
|
allnet,all-wap02860ac|\
|
|
arduino,yun|\
|
|
buffalo,bhr-4grv2|\
|
|
devolo,magic-2-wifi|\
|
|
engenius,eap1200h|\
|
|
engenius,eap300-v2|\
|
|
engenius,eap350-v1|\
|
|
engenius,eap600|\
|
|
engenius,ecb1200|\
|
|
engenius,ecb1750|\
|
|
engenius,ecb350-v1|\
|
|
engenius,ecb600|\
|
|
engenius,enh202-v1|\
|
|
engenius,ens202ext-v1|\
|
|
engenius,enstationac-v1|\
|
|
etactica,eg200|\
|
|
glinet,gl-ar750s-nor|\
|
|
glinet,gl-ar750s-nor-nand|\
|
|
librerouter,librerouter-v1|\
|
|
netgear,ex6400|\
|
|
netgear,ex7300|\
|
|
netgear,wndr4300-v2|\
|
|
netgear,wndr4500-v3|\
|
|
netgear,wnr1000-v2|\
|
|
netgear,wnr2000-v3|\
|
|
netgear,wnr2200-8m|\
|
|
netgear,wnr2200-16m|\
|
|
netgear,wnr612-v2|\
|
|
ocedo,koala|\
|
|
ocedo,raccoon|\
|
|
openmesh,a40|\
|
|
openmesh,a60|\
|
|
openmesh,mr600-v1|\
|
|
openmesh,mr600-v2|\
|
|
openmesh,mr900-v1|\
|
|
openmesh,mr900-v2|\
|
|
openmesh,mr1750-v1|\
|
|
openmesh,mr1750-v2|\
|
|
openmesh,om5p|\
|
|
openmesh,om5p-an|\
|
|
openmesh,om5p-ac-v1|\
|
|
openmesh,om5p-ac-v2|\
|
|
samsung,wam250|\
|
|
ubnt,nanostation-m|\
|
|
yuncore,a770|\
|
|
yuncore,a782|\
|
|
yuncore,xd4200|\
|
|
ziking,cpe46b|\
|
|
zyxel,nbg6616)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wzr-hp-ag300h)
|
|
ubootenv_add_uci_config "/dev/mtd3" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wzr-hp-g300nh-rb|\
|
|
buffalo,wzr-hp-g300nh-s)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
domywifi,dw33d)
|
|
ubootenv_add_uci_config "/dev/mtd4" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
dongwon,dw02-412h-64m|\
|
|
dongwon,dw02-412h-128m|\
|
|
glinet,gl-ar300m-lite|\
|
|
glinet,gl-ar300m-nand|\
|
|
glinet,gl-ar300m-nor|\
|
|
glinet,gl-ar300m16)
|
|
idx="$(find_mtd_index u-boot-env)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
glinet,gl-ar150)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x8000" "0x10000"
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700-v2|\
|
|
netgear,wndrmac-v1)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x10000"
|
|
;;
|
|
netgear,wndr3700-v4|\
|
|
netgear,wndr4300|\
|
|
netgear,wndr4300tn|\
|
|
netgear,wndr4300sw)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
openmesh,om2p-v2|\
|
|
openmesh,om2p-v4|\
|
|
openmesh,om2p-hs-v1|\
|
|
openmesh,om2p-hs-v2|\
|
|
openmesh,om2p-hs-v3|\
|
|
openmesh,om2p-hs-v4|\
|
|
openmesh,om2p-lc|\
|
|
plasmacloud,pa300|\
|
|
plasmacloud,pa300e)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000"
|
|
;;
|
|
qihoo,c301)
|
|
ubootenv_add_uci_config "/dev/mtd9" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
wallys,dr531)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0xf800" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|