ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-29 10:08:59 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
9704d25da1
openwrt/package/firmware/ipq-wifi/Makefile
Robert Marko b126d9c3a3 ipq40xx: add netgear wac510 support 
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.

For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>

Specifications:
SoC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
Flash1:     2 MiB Winbond W25Q16JV SPI-NOR
Flash2:     128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet:   Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
            WAN port active IEEE 802.3af/at PoE in
Wireless1:  Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2:  Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input:      (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs:       Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial:     Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
         The Serial settings are 115200-8-N-1.

Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.

In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.

Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.

Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm

Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:

Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[    1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.

Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[    2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[    2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-06-05 23:29:46 +02:00

142 lines
5.2 KiB
Makefile
Raw Blame History

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/version.mk
PKG_NAME:=ipq-wifi
PKG_RELEASE:=1
PKG_FLAGS:=nonshared
include $(INCLUDE_DIR)/package.mk
define Build/Prepare
mkdir -p $(PKG_BUILD_DIR)
endef
define Build/Compile
endef
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
# to generate the board-* files here.
#
# This is intended to be used on an interim basis until device-specific
# board data for new devices is available through the upstream compilation
#
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
ALLWIFIBOARDS:= \
8dev_habanero-dvk \
aruba_ap-303 \
avm_fritzrepeater-1200 \
buffalo_wtr-m2133hp \
cellc_rtl30vw \
devolo_magic-2-wifi-next \
dlink_dap2610 \
edgecore_ecw5410 \
edgecore_oap100 \
engenius_eap2200 \
engenius_emd1 \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-ap1300 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
luma_wrtq-329acn \
mikrotik_hap-ac2 \
mikrotik_sxtsq-5-ac \
mobipromo_cm520-79f \
nec_wg2600hp3 \
netgear_wac510 \
plasmacloud_pa1200 \
plasmacloud_pa2200 \
qxwlan_e2600ac
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
SUBMENU:=ath10k Board-Specific Overrides
SECTION:=firmware
CATEGORY:=Firmware
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
TITLE:=Custom Board
endef
define ipq-wifi-install-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
endef
define ipq-wifi-install-one
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
)))
endef
# Blank line required at end of above define due to foreach context
define generate-ipq-wifi-package
define Package/ipq-wifi-$(1)
$(call Package/ipq-wifi-default)
TITLE:=board-2.bin Overrides for $(2)
CONFLICTS:=$(PREV_BOARD)
endef
define Package/ipq-wifi-$(1)/description
The $(2) requires board-specific, reference ("cal") data
that is not yet present in the upstream wireless firmware distribution.
This package supplies board-2.bin file(s) that, in the interim,
overwrite those supplied by the ath10k-firmware-* packages.
This is package is only necessary for the $(2).
Do not install it for any other device!
endef
define Package/ipq-wifi-$(1)/install-overlay
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
endef
PREV_BOARD+=ipq-wifi-$(1)
endef
# Add board name to ALLWIFIBOARDS
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984>
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
$(eval $(call generate-ipq-wifi-package,8dev_habanero-dvk,8devices Habanero DVK))
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
$(eval $(call generate-ipq-wifi-package,mikrotik_hap-ac2,Mikrotik hAP ac2))
$(eval $(call generate-ipq-wifi-package,mikrotik_sxtsq-5-ac,MikroTik SXTsq 5 ac))
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
$(eval $(call generate-ipq-wifi-package,nec_wg2600hp3,NEC Platforms WG2600HP3))
$(eval $(call generate-ipq-wifi-package,netgear_wac510,Netgear WAC510))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
Reference in New Issue View Git Blame Copy Permalink