mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 18:19:02 +00:00
8b66f1a06d
For all boards currently working with the mt7530 DSA driver we can be sure that the address of the switch on the MDIO bus is 31 -- simply because that address is hard-coded in the driver and the address from the Device Tree is being ignore. An upcoming patch will add support for MT753x ICs which are programmed to addresses different from 0x1f using bootstrap pins. As a result the address from the Device Tree will then be taken into account, which will break currently working boards which got the address set to anything else than 31. While at it also unify the syntax in Device Tree to always us a decimal value for the 'reg' property. * mt7622-buffalo-wsr-3200ax4s.dts Cosmetic change 'reg = <0x1f>' -> 'reg = <31>' * mt7622-dlink-eagle-pro-ai-ax3200-a1.dtsi Wrong address: 0 -> 31 * mt7622-elecom-wrc-x3200gst3.dts Wrong address: 0 -> 31 * mt7622-linksys-e8450.dtsi Wrong address: 0 -> 31 * mt7622-ruijie-rg-ew3200.dtsi Wrong address: 0 -> 31 * mt7622-xiaomi-redmi-router-ax6s.dts Wrong address: 0 -> 31 * mt7629-iptime-a6004mx.dts Wrong address: 2 -> 31 * mt7981b-zbtlink-zbt-z8102ax.dts Cosmetic change 'reg = <0x1f>' -> 'reg = <31>' Signed-off-by: Daniel Golle <daniel@makrotopia.org>
433 lines
7.2 KiB
Plaintext
433 lines
7.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
#include "mt7622.dtsi"
|
|
#include "mt6380.dtsi"
|
|
|
|
/ {
|
|
model = "ELECOM WRC-X3200GST3";
|
|
compatible = "elecom,wrc-x3200gst3", "mediatek,mt7622";
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
label-mac-device = &wan;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512";
|
|
};
|
|
|
|
memory {
|
|
reg = <0 0x40000000 0 0x1f000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
gpios = <&pio 47 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_WPS;
|
|
};
|
|
|
|
led_power_red: led-1 {
|
|
gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_POWER;
|
|
function-enumerator = <1>;
|
|
};
|
|
|
|
led_power_green: led-2 {
|
|
gpios = <&pio 49 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_POWER;
|
|
function-enumerator = <2>;
|
|
};
|
|
|
|
led-3 {
|
|
gpios = <&pio 50 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_POWER;
|
|
function-enumerator = <3>;
|
|
};
|
|
|
|
led-4 {
|
|
gpios = <&pio 85 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_WHITE>;
|
|
function = LED_FUNCTION_WLAN;
|
|
function-enumerator = <1>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
led-5 {
|
|
gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_WHITE>;
|
|
function = LED_FUNCTION_WLAN;
|
|
function-enumerator = <2>;
|
|
linux,default-trigger = "phy1radio";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&pio 42 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
router {
|
|
label = "router";
|
|
gpios = <&pio 43 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&pio 102 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&cpu0 {
|
|
proc-supply = <&mt6380_vcpu_reg>;
|
|
sram-supply = <&mt6380_vm_reg>;
|
|
};
|
|
|
|
&cpu1 {
|
|
proc-supply = <&mt6380_vcpu_reg>;
|
|
sram-supply = <&mt6380_vm_reg>;
|
|
};
|
|
|
|
&pio {
|
|
eth_pins: eth-pins {
|
|
mux {
|
|
function = "eth";
|
|
groups = "mdc_mdio", "rgmii_via_gmac2";
|
|
};
|
|
};
|
|
|
|
pcie0_pins: pcie0-pins {
|
|
mux {
|
|
function = "pcie";
|
|
groups = "pcie0_pad_perst",
|
|
"pcie0_1_waken",
|
|
"pcie0_1_clkreq";
|
|
};
|
|
};
|
|
|
|
pmic_bus_pins: pmic-bus-pins {
|
|
mux {
|
|
function = "pmic";
|
|
groups = "pmic_bus";
|
|
};
|
|
};
|
|
|
|
pwm7_pins: pwm1-2-pins {
|
|
mux {
|
|
function = "pwm";
|
|
groups = "pwm_ch7_2";
|
|
};
|
|
};
|
|
|
|
/* Serial NAND is shared pin with SPI-NOR */
|
|
serial_nand_pins: serial-nand-pins {
|
|
mux {
|
|
function = "flash";
|
|
groups = "snfi";
|
|
};
|
|
|
|
conf-cmd-data {
|
|
pins = "SPI_WP", "SPI_HOLD", "SPI_MOSI",
|
|
"SPI_MISO", "SPI_CS";
|
|
drive-strength = <16>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
conf-clk {
|
|
pins = "SPI_CLK";
|
|
drive-strength = <16>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
uart0_pins: uart0-pins {
|
|
mux {
|
|
function = "uart";
|
|
groups = "uart0_0_tx_rx" ;
|
|
};
|
|
};
|
|
|
|
watchdog_pins: watchdog-pins {
|
|
mux {
|
|
function = "watchdog";
|
|
groups = "watchdog";
|
|
};
|
|
};
|
|
};
|
|
|
|
ð {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð_pins>;
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
|
|
phy-connection-type = "2500base-x";
|
|
|
|
nvmem-cells = <&macaddr_factory_7fff4>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
|
|
mdio-bus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
switch@1f {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <31>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
|
|
reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
wan: port@0 {
|
|
reg = <0>;
|
|
label = "wan";
|
|
|
|
nvmem-cells = <&macaddr_factory_7fffa>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@4 {
|
|
reg = <4>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
ethernet = <&gmac0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&bch {
|
|
status = "okay";
|
|
};
|
|
|
|
&snfi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&serial_nand_pins>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "spi-nand";
|
|
reg = <0>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
nand-ecc-engine = <&snfi>;
|
|
mediatek,bmt-v2;
|
|
mediatek,bmt-table-size = <0x1000>;
|
|
mediatek,bmt-remap-range = <0x0 0x8c0000>,
|
|
<0x1bc0000 0x30c0000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Preloader";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "ATF";
|
|
reg = <0x80000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
label = "u-boot";
|
|
reg = <0xc0000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "u-boot-env";
|
|
reg = <0x140000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@1c0000 {
|
|
label = "factory";
|
|
reg = <0x1c0000 0x100000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_factory_4: macaddr@4 {
|
|
compatible = "mac-base";
|
|
reg = <0x4 0x6>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
|
|
macaddr_factory_7fff4: macaddr@7fff4 {
|
|
reg = <0x7fff4 0x6>;
|
|
};
|
|
|
|
macaddr_factory_7fffa: macaddr@7fffa {
|
|
reg = <0x7fffa 0x6>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@2c0000 {
|
|
label = "kernel";
|
|
reg = <0x2c0000 0x600000>;
|
|
};
|
|
|
|
partition@8c0000 {
|
|
label = "ubi";
|
|
reg = <0x8c0000 0x1300000>;
|
|
};
|
|
|
|
partition@1bc0000 {
|
|
label = "tm_pattern";
|
|
reg = <0x1bc0000 0x500000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20c0000 {
|
|
label = "tm_key";
|
|
reg = <0x20c0000 0x100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@21c0000 {
|
|
label = "user_data";
|
|
reg = <0x21c0000 0xf00000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30c0000 {
|
|
label = "reserved";
|
|
reg = <0x30c0000 0x4f40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pcie0_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&slot0 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x5000>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
nvmem-cells = <&macaddr_factory_4 1>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
};
|
|
|
|
&pwm {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pwm7_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&pwrap {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmic_bus_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&watchdog_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
};
|