mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 01:59:02 +00:00
b4184c666c
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
75 lines
1.7 KiB
Plaintext
75 lines
1.7 KiB
Plaintext
#
|
|
# Copyright (C) 2016 LEDE
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
ubootenv_mtdinfo () {
|
|
UBOOTENV_PART=$(cat /proc/mtd | grep APPSBLENV)
|
|
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
|
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
|
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
|
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
|
|
|
if [ -n "$nor_flash" ]; then
|
|
ubootenv_size=$mtd_size
|
|
else
|
|
# size is fixed to 0x40000 in u-boot
|
|
ubootenv_size=0x40000
|
|
fi
|
|
|
|
sectors=$(( $ubootenv_size / $mtd_erase ))
|
|
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
|
}
|
|
|
|
case "$board" in
|
|
alfa-network,ap120c-ac|\
|
|
devolo,magic-2-wifi-next|\
|
|
edgecore,ecw5211|\
|
|
glinet,gl-ap1300|\
|
|
glinet,gl-b1300|\
|
|
glinet,gl-b2200|\
|
|
luma,wrtq-329acn|\
|
|
netgear,wac510|\
|
|
openmesh,a42|\
|
|
openmesh,a62|\
|
|
plasmacloud,pa1200|\
|
|
plasmacloud,pa2200)
|
|
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-303)
|
|
ubootenv_add_uci_config "/dev/mtd13" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-365)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wtr-m2133hp)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,ea6350v3)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
linksys,ea8300|\
|
|
linksys,mr8300)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,whw01-v1)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x40000" "0x10000"
|
|
;;
|
|
zyxel,nbg6617)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|