openwrt/target/linux/ath79/dts/qca9558_librerouter_librerouter-v1.dts
Adrian Schmutzler b40e6bc55f ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148)
2020-06-28 14:24:59 +02:00

208 lines
3.2 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
compatible = "librerouter,librerouter-v1", "qca,qca9558";
model = "LibreRouter v1";
aliases {
led-boot = &system;
led-failsafe = &system;
led-running = &system;
led-upgrade = &system;
};
leds {
compatible = "gpio-leds";
system: system {
label = "librerouter-v1:green:system";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
wifi_green {
label = "librerouter-v1:green:wlan2g";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
status_blue {
label = "librerouter-v1:blue:status";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
};
button {
compatible = "gpio-keys";
reset {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
hw_algo = "toggle";
hw_margin_ms = <1000>;
always-running;
};
};
&pcie0 {
status = "okay";
wifi@0,0 {
compatible = "pci168c,0033";
reg = <0x0000 0 0 0 0>;
};
};
&pcie1 {
status = "okay";
wifi@0,0 {
compatible = "pci168c,0033";
reg = <0x0000 0 0 0 0>;
};
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&usb_phy0 {
status = "okay";
};
&usb0 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
};
&usb_phy1 {
status = "okay";
};
&usb1 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x050000 0x7c0000>;
};
partition@810000 {
label = "fw2";
reg = <0x810000 0x7d0000>;
};
partition@fd0000 {
label = "res";
reg = <0xfd0000 0x20000>;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
0x04 0x87600000 /* PORT0: RGMII, MAC0/6 exchage, tx_delay 01, rx_delay 10 */
0x0c 0x00000080 /* PORT6: SGMII */
0x10 0x81000080 /* POWER_ON_STRAP: LED open drain, SerDes auto-neg disabled */
0x50 0xcf37cf37 /* LED_CTRL0 */
0x54 0xcf37cf37 /* LED_CTRL1 */
0x58 0xcf37cf37 /* LED_CTRL2 */
0x5c 0x0 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
0x94 0x0000007e /* PORT6 STATUS */
>;
};
};
&eth0 {
status = "okay";
pll-data = <0xa6000000 0x00000101 0x00001616>;
mtd-mac-address = <&art 0x0>;
phy-handle = <&phy0>;
};
&eth1 {
status = "okay";
phy-mode = "sgmii";
pll-data = <0x03000101 0x00000101 0x00001616>;
mtd-mac-address = <&art 0x6>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0xc>;
};