openwrt/target/linux/ath79/dts/ar9331_etactica_eg200.dts
Adrian Schmutzler 008db6b970 ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.

So, do not disable it in the first place, and drop all device-specific
status statements afterwards.

Though this is a cosmetic commit, it might be a pitfall for
device-support backporters if missing. Since backporting it is trivial,
let's just do it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit dc1280ef65)
2020-08-18 17:45:20 +02:00

126 lines
1.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9331.dtsi"
/ {
model = "eTactica EG200";
compatible = "etactica,eg200", "qca,ar9331";
aliases {
serial0 = &uart;
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <50>;
restore {
linux,code = <KEY_RESTART>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&switch_led_disable_pins>;
modbus {
label = "eg200:red:modbus";
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
};
etactica {
label = "eg200:red:etactica";
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
};
eth0 {
label = "eg200:red:eth0";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
wlan {
label = "eg200:red:wlan";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
};
&uart {
status = "okay";
};
&usb {
dr_mode = "host";
status = "okay";
};
&usb_phy {
status = "okay";
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x0>;
gmac-config {
device = <&gmac>;
switch-phy-addr-swap = <1>;
switch-phy-swap = <1>;
};
};
&eth1 {
status = "okay";
compatible = "syscon", "simple-mfd";
};
&spi {
num-chipselects = <1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot@0 {
reg = <0x0 0x40000>;
read-only;
};
uboot-env@40000 {
reg = <0x40000 0x10000>;
read-only;
};
firmware@50000 {
compatible = "denx,uimage";
reg = <0x50000 0xfa0000>;
};
art: art@ff0000 {
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0x1002>;
};