mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
d82d84694e
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
50 lines
1.2 KiB
Plaintext
50 lines
1.2 KiB
Plaintext
CONFIG_AT803X_PHY=y
|
|
CONFIG_AR8216_PHY=y
|
|
CONFIG_DMADEVICES=y
|
|
CONFIG_DMA_ENGINE=y
|
|
CONFIG_DW_DMAC_CORE=y
|
|
CONFIG_DW_DMAC=y
|
|
# CONFIG_SATA_DWC_OLD_DMA is not set
|
|
# CONFIG_DW_DMAC_PCI is not set
|
|
CONFIG_IKAREM=y
|
|
CONFIG_ATA=y
|
|
CONFIG_ATA_SFF=y
|
|
CONFIG_ATA_BMDMA=y
|
|
# CONFIG_PCI_DISABLE_COMMON_QUIRKS is not set
|
|
CONFIG_SATA_PMP=y
|
|
CONFIG_GENERIC_PHY=y
|
|
CONFIG_SATA_DWC=y
|
|
# CONFIG_SATA_DWC_DEBUG is not set
|
|
CONFIG_SCSI=y
|
|
CONFIG_BLK_DEV_SD=y
|
|
CONFIG_GPIOLIB=y
|
|
CONFIG_GPIO_GENERIC=y
|
|
CONFIG_GPIO_GENERIC_PLATFORM=y
|
|
CONFIG_LEDS_TRIGGER_DISK=y
|
|
CONFIG_RTC_CLASS=y
|
|
CONFIG_RTC_DRV_M48T86=y
|
|
CONFIG_THERMAL=y
|
|
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
|
|
CONFIG_THERMAL_OF=y
|
|
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
|
|
CONFIG_THERMAL_HWMON=y
|
|
CONFIG_HWMON=y
|
|
CONFIG_SENSORS_GPIO_FAN=y
|
|
CONFIG_CMDLINE="rootfstype=squashfs noinitrd"
|
|
CONFIG_MTD_UBI=y
|
|
CONFIG_MTD_UBI_BEB_LIMIT=20
|
|
CONFIG_MTD_UBI_BLOCK=y
|
|
# CONFIG_MTD_UBI_FASTMAP is not set
|
|
# CONFIG_MTD_UBI_GLUEBI is not set
|
|
CONFIG_MTD_UBI_WL_THRESHOLD=4096
|
|
CONFIG_UBIFS_FS=y
|
|
# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
|
|
CONFIG_RTL8366_SMI=y
|
|
CONFIG_RTL8367B_PHY=y
|
|
CONFIG_SENSORS_LM90=y
|
|
CONFIG_SENSORS_TC654=y
|
|
CONFIG_SWCONFIG=y
|
|
CONFIG_SWCONFIG_LEDS=y
|
|
CONFIG_WNDR4700=y
|
|
|