openwrt/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
Tobias Schramm fa3c2676ab ath79: Add support for Ubiquiti Nanostation AC
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Switch: QCA8334
Ports:  2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN:   5 GHz QCA899X (PCI) and 2.4 GHZ AR9342

Successor to the old NanoStation M5 with AC wireless.

The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).

Serial

Serial settings: 115200, 8N1

* = plated through hole
0 = nylon screw

      [Top of device]
+--------------------------+
|    [label]               |
|  0                       |
|                    0     |
|         [ubnt]           |
|         [logo]  3V3  *   |
|                  TX  *   |
|                  RX  *   |
|                 GND  *   |
|                          |
|                      *   |
|                      *   |
|                      *   |
|                      *   |
|    0                     |
|                 0        |
|                          |
|                          |

Installation

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-10-07 10:46:20 +02:00

135 lines
3.0 KiB
Bash

#!/bin/sh
. /lib/functions/k2t.sh
# xor multiple hex values of the same length
xor() {
local val
local ret="0x$1"
local retlen=${#1}
shift
while [ -n "$1" ]; do
val="0x$1"
ret=$((ret ^ val))
shift
done
printf "%0${retlen}x" "$ret"
}
ath10kcal_die() {
echo "ath10cal: " "$*"
exit 1
}
ath10kcal_from_file() {
local source=$1
local offset=$2
local count=$3
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $source"
}
ath10kcal_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath10kcal_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $mtd"
}
ath10kcal_patch_mac() {
local mac=$1
[ -z "$mac" ] && return
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
}
ath10kcal_patch_mac_crc() {
local mac=$1
local mac_offset=6
local chksum_offset=2
local xor_mac
local xor_fw_mac
local xor_fw_chksum
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
ath10kcal_patch_mac "$mac" && {
xor_mac=${mac//:/}
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
}
}
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions.sh
. /lib/functions/system.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
ocedo,koala)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
;;
openmesh,om5p-ac-v2)
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
tplink,archer-c7-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
;;
tplink,re450-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
ubnt,unifiac-lite|\
ubnt,unifiac-mesh|\
ubnt,unifiac-mesh-pro|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,unifiac-pro)
ath10kcal_extract "EEPROM" 20480 2116
;;
esac
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
esac
;;
*)
exit 1
;;
esac